DIY table floor lamp. DIY table lamp: electrical, lighting, construction, design. Round lampshades made of threads

Lighting fixtures in an apartment should provide two types of lighting: bright and dim. WITH bright lighting Chandeliers mounted on the ceiling usually cope. But what to do when you need to increase the access of light when working behind the scenes? desk or when reading a book before bed? Help here table lamp. The advantage of such a device is that it does not illuminate the entire room, but only a certain area, without disturbing other family members.

Figure 1. Diagram of a table lamp.

Today, consumers are offered a wide variety of lamps, but you can make them yourself. In order to assemble a lamp with your own hands, you do not need to be a professional electrician. A great desire and minimal skills will allow you to decorate your apartment with an original and functional piece of furniture. The following methods can be used to make lighting fixtures.

Original table lamp made of bars

Handmade has always been valued by lovers of the finest. Now it is very popular, which means that any item made by hand will take its rightful place in the interior of the apartment, for example, original lamp from wooden beam(Fig. 1).

To manufacture the device you will need the following accessories:

hacksaw;
screwdriver;
drill;
bolt with wing nut;
a can of gold-plated paint;
3 wooden bars(1 long and 2 short);
electrical kit (cord, light bulb, socket, plug).

Figure 2. Sconce connection diagram.

In order to make a lamp, first of all you need to saw off 3 bars using a hacksaw. Their length can be any, but the condition must be met: the first bar must be larger size, and the other two are shorter and of the same length.

Then a hole is drilled at the ends of the short bars at an equal distance from the edge. Two similar holes must be made in the long bar: in the middle for the bolt, and in the upper part for the power cord. The distance of the first hole from the edge will determine the angle of the lamp. When the holes for the bolt are prepared, the short bars are pressed parallel to the long one, and the entire structure is fastened with a bolt and a wing nut.

To give the device an attractive appearance, the cord and socket must be treated with spray paint. When the paint has dried, the cord is threaded through the top hole in the long bar, and the cartridge is mounted on it. A plug for the socket is attached to the other end of the cord. The lamp is ready. Its laconic but unusual design will successfully decorate your desktop.

Return to contents

Table lamps with homemade lampshades

If you have an old and useless table lamp lying around in your closet, you can give it a second life by making a fashionable lampshade. These items combine elegant chic with a touch of glamor, and are extremely easy to make. In addition, you can achieve the desired degree of illumination.

For example, a lamp made of dense fabric will give a soft and diffused light, due to which it can be used as a night sconce (Fig. 2). If threads are used for the lampshade, the lamp can be used to illuminate the work surface.

To make a lamp with soft light, you will need:

old lamp with lampshade;
matte paint that matches the color of the room interior;
soft dense fabric (chintz, satin, etc.);
a paper stencil in the form of a circle with a diameter of 10 cm;
glue gun

First of all, you need to prepare strips of fabric 10 cm wide, then cut them into equal squares. To cover the lampshade you will need at least 200 squares. After this, you need to cut out circles from each square using a stencil.

In order for the lamp to best match the interior design, the old lampshade can be painted. If you apply the dye in uneven strokes, the lamp will look more original. While the paint dries, you should make parts from rag circles to create a lampshade.

Each detail should be shaped like a badminton bag or shuttlecock. To give the part this shape, the center of the circle must be coated with glue using glue gun, and then gather the sides of the circle in the center and compress them.

When the paint has dried, the base of the prepared parts is smeared with glue and applied to the lampshade. You can glue the rag rounds either tightly or a little looser. The intensity of lighting depends on this. In order to create additional decoration for the lamp, the edges of the flounces can be sprinkled with golden or silver paint.

Return to contents

Lamp with thick thread lampshade

To make a lampshade you will need threads, PVA glue and balloon ik.

You can create an unusual table lamp or floor lamp from thick threads. For work you will need the following items and materials:

an old lamp without a lampshade;
balloon;
PVA glue;
saucer for glue;
thick cotton threads of the desired color.

The operating algorithm is extremely simple. First of all, you need to inflate the balloon and tie the hole tightly so that the balloon does not deflate. Then a small amount of glue is poured into the saucer. The threads can be cut into pieces or you can use a single thread, unwinding it from a bobbin.

The main task is to tightly wrap the ball with threads, leaving space at the bottom, in order to then pull out the unnecessary ball. The threads are dipped in glue, then carefully wrapped around the ball. The coils should fit snugly against each other. You can completely cover the ball with thread or leave gaps. For strength, the ball already covered with threads can be additionally coated with a layer of glue.

Then the product is left to dry completely: this usually takes at least 8-10 hours. When the glue has dried, deflate the balloon and remove it from the resulting structure. A very light and elegant lampshade that fits onto the base of the lamp. If desired, the lampshade can be decorated paper butterflies, beads, bugles or braid.

Return to contents

Unusual lamp made from old photographic films

A lamp made from photographic films will fit perfectly into a retro-style interior.

You can create an even more unusual lamp using old photographic films. Such a lighting fixture will fit well into both a retro-style design and the interior of a room in the Art Nouveau style. To work you will need to prepare:

base for the lamp;
well-bending wire for making a frame;
a sheet of thick matte paper;
glossy glue for decorative works;
old photo or film;
centimeter;
scissors;
glue brush.

Work must begin with the manufacture of a frame for the lampshade.

As a stencil, you can use any object in the shape of a parallelepiped, for example, cardboard box. Then the end parts of the frame should be covered with thick paper.

After this, you need to measure the height of the frame and cut the strips of photographic film into pieces corresponding to it. Then the frame is well coated with decoupage glue. Strips of film are applied to the paper and held for some time to “set”. Photographic film can be glued both vertically and horizontally. In the second case, it is possible to see the images. In addition, you can be creative with the design and place films or on each side under different angles, or diagonally.

Then you need to give the product time to dry. Particular care must be taken to ensure that all corners and ends of the film are glued. After the glue has dried, the frame is coated with the adhesive again (on top of the film). When everything is completely dry, the lampshade must be placed on the base. The lamp is ready, it will perfectly decorate the interior of the apartment.

DIY table lamps are the simplest lighting devices. They are compact in size and light weight, so they can be installed not only on a desktop, but also on a small coffee table or bedside table in the bedroom. Despite the fact that table-type lamps do not play a big role in the interior design of the room, they still give the room a more comfortable and cozy homely atmosphere with their decorativeness and functionality.

Such lighting equipment can easily be manufactured independently in living conditions from a wide variety of scrap materials, old unnecessary items. For example, many people don’t even realize that there are craftsmen who make unique designer floor lamps, chandeliers, table lamps, other decorative lighting devices from the following items:

ordinary glass bottles from wine;
glass, metal cans;
flower pots;
tin cans for beer, cola, and other soft drinks;
plastic disposable tableware;
nylon threads and wire;
thick paper or cardboard;
other, at first glance, unnecessary things.

In this article:

Table lamp made of bars

Handmade has always been quite in demand among lovers of the finest. And today it is extremely popular, which means that any product made by hand will find a worthy place in the interior design of an apartment or own home. For example, such an item could be a designer lighting fixture made of wooden beams.

screwdriver;
hacksaw;
drill;
gilded paint in a can;
wing bolt and nut;
long wooden block - 1 pc., short - 2 pcs.;
electrical kit: socket, plug, cable and light bulb.

Manufacturing instructions

Initially, you need to make three pieces of timber of any length, but the main condition: one bar must be longer than the other two, and the latter must have the same length.
Holes are drilled at the ends of two short bars at the same distance from the edge. Similar holes need to be made in the long block: one in the center for the bolt, the second in the upper part for the electrical cable. The distance from the edge of the first hole depends on the intended angle of the lamp.
After preparing the hole for bolted connection short bars parallel to each other need to be pressed against a long bar, the resulting structure is connected with a bolt and a wing nut.
Now you need to thread the electrical cable through the top hole in the long bar and secure the socket. A plug is connected to the second end of the cable to connect the lamp to the mains voltage.
The original table lamp is ready for use.

If desired, you can pre-tint the cartridge and cable with spray paint, let them dry thoroughly, and only then install them in their place. This will make the product more attractive appearance.

DIY table lamp shade

If there is an old table lamp lying somewhere in the household that no one needs, it can be given a second life. To do this, you just need to make an unusual designer lampshade with your own hands, which does not present any difficulties or material costs.

Using a homemade lampshade for a lamp, you can achieve the most optimal fit for the room or working area illumination, for example:

the lighting source will provide soft diffused light through thick fabric - this is an excellent option for the bedroom, the lamp can be used as a night light;
If the lampshade is made from threads, then such a lighting device is suitable for illuminating a work surface.

Required materials and tools:

old lamp with lampshade;
dense soft fabric, for example, satin or chintz;
matte paint (color to suit interior solution rooms);
glue gun;
cardboard stencil of a circle (D=100 mm).

Manufacturing instructions

Initially, you need to cut fabric strips 10 cm wide and cut them into equal squares (approximately 200 such pieces are needed).
Circles are cut out from prepared fabric squares using a stencil.
The old lampshade needs to be painted color scheme interior of the room. The lamp will look more original if the paint is applied in uneven strokes, that is, to give the surface relief.
While the paint is drying, you can start making parts for the lampshade from prepared fabric circles. Each resulting element should look like a badminton shuttlecock or a folded paper bag for sunflower seeds. To give the blanks a similar shape, the center of the circle is coated with glue, then the sides of the circle are compressed in the center.
After the painted lampshade has completely dried, you can begin decorating it with fabric blanks. The parts are smeared with glue and pressed against the surface of the lampshade.

If desired, the edges of the fabric flounces can be lightly sprayed with gold or silver paint from a spray can. This will further embellish the finished product.

Important! Depending on the intensity of luminous flux required from the lamp, decorative elements glued either tightly enough to each other, or more loosely.

Homemade thread light

To create an original table lamp or floor lamp, you can use ordinary thick threads.

Required materials and tools:

children's balloon;
an old lighting fixture without a lampshade;
thick cotton threads (the color is selected to match the interior of the room in which the decorative light is planned to be used);
PVA glue and an unnecessary container for it (you can take a plastic disposable plate, cut a container from a plastic bottle, etc.).

Manufacturing instructions

Inflate the balloon and tie the hole tightly to prevent air from escaping.
Pour a large amount of glue into the prepared container.
You can use a whole thread, gradually unwinding it from a spool, or cut it into separate pieces in advance. The goal is to tightly wrap the threads around the entire surface of the ball (it is necessary to leave a small space at the bottom so that the deflated ball can then be removed).
Before wrapping the frame with threads, they must be thoroughly soaked in glue. Each subsequent turn should fit tightly to the previous one. You can completely cover the ball with threads or leave equal gaps after several turns (the intensity of the light flux will depend on this). To make such a lampshade more durable, it is recommended to coat the threads already placed on the ball frame with glue again.
The product must be allowed to dry completely (this may take up to 10 hours).
After the glue has completely dried, the ball can be deflated and removed from the resulting structure.
The exclusive lampshade is ready, it can be placed on the lamp.

If desired, a hand-made table lamp can be additionally decorated with other decorative components, for example, braid, beads, homemade paper butterflies, etc.

Table lamp made of pebbles and wood

Natural materials, for example, pebbles, pieces of wood, are ideal for making a decorative lamp.

Required materials and tools:

5 pieces of wood (knots, fragments of driftwood, etc.);
three round or oval stones (marble, sea pebbles, etc.);
reed branch;
electrical cable with socket;
pin for table lamps (D=10 mm);
2 nuts (D=10 mm);
metal knife;
electric drill;
set of drills for wood, concrete.

Manufacturing instructions

Preparation consumables. It must be thoroughly washed and dried.
Next from wood materials the most massive, stable piece is selected, which will be used as a stand for a table lamp. A hole is made in it with a drill for a pin, which is first trimmed to the required parameters with a metal knife. The height of the stud should be approximately 5 cm higher than the level of stones and wooden blanks stacked on top of each other.
The pin is inserted into a hole made in a wooden base.
Using different drills in each prepared stone and wooden blank holes are made to fit the diameter of the stud. All made parts are threaded onto a pin already fixed at the base.
At the very end, a reed branch is put on the hairpin (it will cover the thread).
Next, a cartridge is attached to the end of the pin (in this case electrical wire remains outside), the light bulb is screwed in, and a decorated lampshade is installed.

For your information! To secure the cable along the base of the lighting fixture, you can attach a small spring or a piece of thin wire.

This DIY design invention fits perfectly into a rustic, ethnic style, most best option installations - country house.

In addition to the options described above for manufacturing exclusive lighting fixtures, there are many more. From scrap materials you can make lighting devices from LED strips and other lighting devices for any room, for any interior at home.

Lighting is the most important component of the interior. The coziness and level of comfort of our home depends on lighting. The play of light and shadow allows you to play up the winning moments of the interior and divert attention from the unsuccessful moments. And also - lamps, floor lamps, chandeliers and lamps create the atmosphere that we call “home”. They will help you make your home “your own”, personal and individual. unique lamps And best way- make a lampshade with your own hands. Homemade lampshades and lampshades are the thing that will make your home stand out from others.

A few words about safety

In the manufacture of lamps, floor lamps and chandeliers in industrial conditions calculation is made in advance minimum distance from the “body” of the lamp to the materials. This distance depends on the power and thermal radiation of the lamp and on the type (flammability) of the material from which the lampshade/shade is made. At home, it is unlikely that anyone will bother with such calculations. And in order not to create a dangerous situation, you should adhere to certain rules.

In general, after making a lampshade and installing it, in the first few days pay attention to whether the lampshade is heating up. Heating is any increase in temperature above environment. If the lampshade feels “warm”, change the bulb to a less powerful one. Check again. Do this until the homemade lampshade gets warm.

Where to get the frame

If you want to remake an old lamp, floor lamp, sconce whose old lampshade has become unusable, you can simply use the existing base, stripping old material. Before starting work, carefully inspect the frame, if there is rust or damaged coating, maybe I should strip everything off and paint it again? At the same time, the color can be changed. If there are no old frames, you can buy an inexpensive lamp (in a store or at a flea market) and do the same operations with it. By the way, good lampshades can be made from waste baskets. There are wire ones and there are plastic ones. The main thing is to find the right shape and size. Then make a hole in the bottom for the cartridge. Then it’s a matter of decoration/plating, but here there are a lot of options.

If this method is not available, you can make a lampshade without a frame (there are some) or make a frame yourself. The material for making a frame for a lampshade with your own hands is: wire, wood (wooden or bamboo sticks, specially cut elements), plastic bottles.

How to make a frame for a homemade lampshade from wire

The wire for the lamp frame needs aluminum or steel. Aluminum is easy to work with, but it wrinkles easily. This is not very important when the lampshade is already in use, but this fact must be taken into account during work: the shape can be ruined. On the other hand, such plasticity allows you to easily and simply make changes to the shape during work. So it's a good option. Aluminum wire can be “mined” from electrical cables. You will have to remove the protective shell and you can use it.

Steel wire is more elastic, so it retains its shape well. You can search for it on construction market. It's more difficult to work with. It is advisable to have strong male hands nearby.

In addition to the wire, you will need powerful wire cutters and pliers for the job. The lampshade frame usually consists of two rings and posts connecting them. The shape of the future lampshade depends on the size of the rings and the shape of the stands. Questions may arise regarding the number of racks and methods of their fastening. The number of posts depends on the size of the rings and how “round” you want the lampshade to be. The more stands, the smoother the fabric will lie. So it's up to you to choose, but optimal distance between the posts in the bottom circle - about 5-6 cm.

Techniques for creating a wire lampshade frame

How you attach the stack to the lampshade rings depends on the thickness and type of wire, as well as the tools you have. The easiest one is to make a small hook at the end, then clamp it tightly. To prevent the ring from sliding left and right, first treat the wire at the attachment point sandpaper with large grains. This is an option for thick aluminum wire. If the wire is steel, with a diameter of 1.2-2 mm or more, the best way is. Thinner wire can be bent and wrapped around a ring or also made into a hook.

If you make hooks and wrap wire, the appearance is far from being as ideal as that of factory frames. But this imperfection will be covered by the lampshade itself. If you still care about it, find the tape suitable color(usually matched to the color of the lampshade) and carefully wrap the resulting frame. It will get much better. The tape can be coated with PVA glue and, wet, tightly, turn by turn, wrapped around the frame.

Wire mesh

If you can find a mesh of thin wire, you can quickly make an almost perfect cylindrical lampshade for a floor lamp, table lamp, night light, lampshade for placing a candle, etc. All you need to do is cut a piece of mesh of the required length and width, roll it into a ring and secure the wires by wrapping them around the posts.

To prevent the mesh from straightening out, when cutting a piece, cut so that there are long free ends on both sides. We will use them to fasten the cylindrical lampshade. And the imperfection of the upper and lower rings can be masked with a ribbon of the desired color.

From a five liter plastic bottle

An interesting shaped lampshade can be made from a large plastic bottle. There are bottles for 5-6 liters and even 10. These are what you can use. Cut off the top or bottom of the container, depending on what you like best. In the cut off part we make a ring for the cartridge. If cut off upper part, for some cartridges you can use a neck. For those with a larger diameter, it will have to be cut off.

Then we cut out the excess plastic and form the rims and pillars of the lampshade. To avoid mistakes, you can first draw all the lines with a marker. It will be easier to cut. Everything is elementary. Then we just decorate. And yes, it is necessary to cut out the plastic, otherwise warm air there will be nowhere to go.

Making lampshades on a frame

There are enough options for how to make a lampshade cover:

From tapes

The easiest and fastest way to transform an old lampshade for a floor lamp or table lamp is to use ribbons. You need a frame or lampshade in the form of a cylinder. He may be naked or covered with fabric. If you use a “bare” frame, light will shine through the cracks, which will create interesting lighting effects, but the lighting will be uneven. It is uncomfortable to read in such light - this is an interior solution. If you need even lighting, first cover the frame with fabric. It can be the same color as the ribbons, a couple of shades darker or lighter, or it can be contrasting. It all depends on your desire. And remember that the darker the fabric, the less light misses the lampshade.

We take a ribbon 1-2.5 cm wide. We fix it on the wrong side of the lampshade using PVA glue, additionally securing it with a pin. If you took a wire frame without fabric, attach it to the upper or lower rim (you can sew it on by hand, you can use glue). Then we begin to wrap the entire frame, from top to bottom, placing the turns of tape close to each other, but without overlapping.

Having completed the circle, turn the tape 90°. We fix it in this position (with a needle and thread or PVA glue, glue from a gun, temporarily fixing it with a pin, pressing it with a clothespin). Then we pass the tape under the first tape, pull it out, lay it on top of the second, then pull it down again, pull it up through one tape. So, gradually, we create an interlacing, filling the entire lampshade.

Alternatively, you can pass two vertical strips at a time. But then you need to make sure that each next row moves one crossbar. Then you get a different type of weave. This type of lampshade is ideal for floor lamps, since the light will be directed downwards and the dispersion through the walls will be small.

In this version, the ribbons can be the same, they can be the same color, but of different textures, they can differ by a couple of tones or be contrasting. The tapes can be passed in a circle in a continuous stream, or after a certain distance. If you find a wide tape and apply it with an overlap, then you won’t need horizontal ones at all. And if you use a braided or twisted cord (in the lower photo on the right), we will get a completely different-looking lampshade. So this lampshade finishing technique alone gives you a lot of options.

Let's briefly present the ideas. There are many options for how you can design standard frames for lampshades in a non-standard way. The first method has already been announced: you can knit or crochet a cover for a lampshade. Several options in the photo.

Not everyone knows how to knit. It is easier to work with beads, especially if you glue them. Decorate old fabric You can use beads, sequins, beads of different shapes and sizes. You can make this “new-old” lampshade with your own hands in a couple of hours. Select decorations that match the color, coat the fabric with PVA glue, and stick on the decorations. To complete the look, you can use beads to assemble pendants that are attached to the lower rim, but this is already painstaking work. The effect is interesting though.

You can sew a new lampshade from fabric. But it doesn’t have to be an updated copy of the old one. You should use your imagination! If a lamp or floor lamp is in the girls' room, new case The lampshade can be made into a skirt. You choose the style of the skirt yourself. They look interesting when folded. With and without ruffles.

In a boy's room you can use an old one geographical map. They are on thick paper. If the paper is not thick enough, you first need to glue the card onto the cardboard, and then glue the lampshade from such a blank.

Original lampshades are obtained if the finished frame is braided with threads or ropes. Ropes can be natural. In this case they are gray, brown and beige. You can find thin synthetic colored cords. They will make products that are more “cheerful” in color. The situation is even simpler with knitting threads. They are thin, thick, textured, with smoothly changing colors. In general, there are a lot of options.

We take the frame and braid it according to a certain pattern. You can start with the racks. Braid each stand with a braid (the length of the threads should be 3 times the height of the stand). When this work is completed, we begin to stretch the threads/ropes between the posts. They will need to be passed through the braids, so with threads it is more convenient to do this with a needle, but ropes can be inserted this way.

The second option is to first entangle the entire frame horizontally, and then braid the racks. The braid won't work here, you just need to secure the turns to the stand using inclined stitches with a certain slope. This option is somewhat simpler in execution, but the “braids” look more decorative.

Homemade lampshades without frame

Many materials are rigid enough to hold their shape on their own, but at the same time they are flexible enough to make something interesting out of them. Such homemade lampshades Well, a lot. And almost all of them are worth your attention. We will present here only part, the other part will go in the section with photos (see below).

From knitted lace doilies

Many people have crocheted napkins and they lie in “stashes”, because it’s a pity to throw them away and they don’t know how to use them. There is a very interesting idea - to make a lampshade out of them for a hanging chandelier. In addition to napkins, you will need a large balloon or inflatable ball, glue for heavy wallpaper (vinyl, silk-screen printing, etc.), and a brush.

Soak the glue according to the instructions and wait until it swells. We inflate a balloon or take a ball and hang it up. When the glue is ready, lay out a napkin on some clean surface, coat it with glue, and place it on the ball.

It must be laid out in such a way that there will be a hole in the center for the cartridge. We glue the napkins one by one. They need to be laid out so that the edges overlap slightly. When all the napkins are laid out, coat them with glue again and leave until dry. When the glue has dried, deflate the ball or ball (the ball can be pierced, if you don’t mind) and take it out through the hole. That's all, the lace lampshade is ready.

In some cases, problems arise with how to hang the finished lampshade on the socket. The problem is solved simply - take a transparent plastic bottle, cut off its neck, if necessary, expand the hole to required sizes(so that it fits tightly onto the socket), then cut the plastic so that you get a ring 5-7 cm wide. Coat this ring with PVA glue, and glue it to the lampshade from the inside of the ball.

Round lampshades made of threads

Almost the same technology can be used to produce round and semicircular stylish lampshades. Choose threads of a suitable color. Their composition is absolutely unimportant - what matters is color, thickness and texture. They can be shaggy, smooth, twisted, thinner and thicker. The appearance depends on this. It is most convenient to work with cotton threads of medium thickness. They absorb glue well and then, after drying, keep their shape perfectly.

You will also need a ball or ball. This will be the base of the lampshade, which gives the shape. You can choose the dimensions of the base as desired. The threads will need to be glued together; for this you will need PVA glue. It is poured into a container and diluted with water in a 1:1 ratio.

You can use other glue. It is important that it becomes transparent after drying. This is WB-29 from TYTAN Professional and D2 glue for carpentry. If you use any of these types of glue, read the instructions.

On the ball or sphere we will draw a circle, which will be slightly smaller in size than the lamp socket. On the opposite side, draw a larger circle - this will be the lower edge of the lampshade. Now everything is ready, we can start.

We coat the threads with glue and wind them around the ball in a chaotic manner. It’s more convenient to do this if the glue is poured into a container - you can put the whole skein in there and just pull the thread slowly. With glue in a tube, everything is not so comfortable: you have to coat sections up to a meter long, wrap it around, and coat it again. It takes much longer. This is if you do not use PVA. But the products turn out to be more rigid and do not sag or change shape over time, as can happen with PVA thread lampshades.

When winding threads around the ball, carefully go around the drawn circles. If you accidentally climbed into the “forbidden territory”, simply move the threads, forming a smooth (more or less smooth) edge. When the threads run out or you decide that the density is enough, the process can be stopped. We tuck the edge of the thread between the others. All. Next, coat the ball with wound threads again with glue (PVA can be poured over) and leave to dry (at least 2 days). To prevent the ball from rolling, we find a bowl or pan and use it as a stand.

The last stage is to deflate the ball or sphere. If the ball has a nipple, press it with a thin wire, releasing the air. We take out the deflated ball. That's all, you can thread the lamp inside and test the lampshade.

The technology is the same, but the appearance is very different...

Using the technology described above, you can make not only round lampshades. Rectangular, triangular, trapezoidal. Choose a base that is easy to remove, wind threads soaked in glue, braid, even sticks, newspaper tubes, etc. After drying, remove the base and voila, you have made a lampshade with your own hands. A couple of examples in the photo below.

You can also use chopsticks... Just wrap the ball too cling film and do not use PVA glue, but transparent carpentry glue

It's pasty polymer clay in a tube, which was applied to a milk carton, then dried and the bag was removed...

Creative homemade shades for lamps, floor lamps and chandeliers

It’s simply amazing what people don’t make beautiful and unusual things out of. A lampshade made from a cup, grater, bottle, beer or glass jar, metal parts and beer can rings... It seems everything can be used...

Lampshade made from an old sieve... stylish

Candlesticks turn into lamps... without lampshades

You can't tell in real life, but these lampshades are made from hooks used to open metal drink cans and canned goods... if you paint them, it will be even more interesting

Don't know what to do with grandma's crystal? Make lampshades out of it...

Handmade items fill the home with special warmth and comfort. In addition, they turn out to be exclusive. We offer an overview of lamps that will completely change the atmosphere in the room, turning into an object of envy from the groans of friends and relatives. Moreover, they are made from everyday items that are usually thrown away.

Cardboard bags for juices or other drinks are a fairly common thing in most homes. Most often it is thrown away. But Malayan designer Edward Chu spent a lot of time cutting them into hundreds of strips and making amazing lamps from them without a drop of glue, a simple origami principle.

Yaroslav Olenev proposed making lamps from disposable ones plastic spoons and became the winner in the Ecology and Design category from the Future Now magazine.

No less original application I also found Natalie Simpson for ordinary wooden hangers. But they look amazing in the form of a chandelier.

Kevin Champeny must be given his due; not everyone has the strength and patience to string 14 thousand bears to get a chandelier.

Tira Hilden and Pio Diaz have their own vision of the problem of housing lighting. Their lamps make the room look like a forest. All the walls come to life and turn into trees.

A talented welder, Matt Ludwig also turned out to be an excellent designer. For the restaurant "JJ's Red Hots" he made an incredible original chandelier from the old one drum set.

Texas artists Joe O'Connell and Blessing Hancock used parts from old bicycles to create stunning lamps and hang them in a tunnel under the highway.

It will probably be difficult to find a more original chandelier than one made from a pumpkin by a Polish artist. He carves stunning patterns into the peel that never repeat.

Lampshades made from felt hats from Jeeves & Wooster look original and stylish.

One day, Heather Jennings saw an amazing Rhododendron chandelier in a store, but it cost more than $800. Then the designer decided that she could do no worse with her own hands. For this she needed paper cupcake liners.

11. Chandelier for the kitchen

A chandelier made from ordinary metal tetrahedral graters will look incredibly beautiful.

Vases and candy bowls made from openwork napkins are still fresh in my memory. Now it's time to knit chandeliers.

Fansua Lego offers a strange option; he believes that the best way to store cutlery is a chandelier.

A large cloud is cut out of wood, but the rest and the switch are made of cardboard.

Several globes can make a wonderful cascading chandelier, a great way to illuminate a flight of stairs.

Table lamps- far from being the most necessary lighting devices. However, it is thanks to them that the atmosphere becomes comfortable and cozy. Among other lighting elements, table lamps are the easiest to install, compact, lightweight and versatile. It is not necessary to go shopping to add such a device to the interior. You can add originality and create a unique one-of-a-kind device or resort to restoration of an old lamp. You can learn how to make a table lamp with your own hands from the article.

Attributes for needlework

Desk lamp can be created with your own hands from absolutely any necessary and unnecessary things. Everyone in the house has old items that they couldn’t throw away, but there was also nowhere to use them. It's time to give them a second life.

To decorate a lampshade or lampshade, you can use the following details:

beads, seed beads, glass beads, sequins, stones, shells, buttons;
cocktail umbrellas revealing tin can details;
plastic bottles, spoons, forks, lids, yogurt, tin and other jars;
fabrics and textiles, braid, ribbons, threads, bows;
newspapers and paper clippings, drawings for decoupage techniques;
toys, both soft and hard, right down to the smallest kinder surprises.

As a base for a table lamp, you can cut wooden stands with your own hands or use ready-made ones from under something. You can also use flower pots, plates, an updated base from an old lamp and many other items, or do without a base at all.

The frame for creating a lampshade can be a sphere or a ball, which can be easily removed at the end of the work.

The easiest way to liven up your interior with a new lamp is to repair the old one.

Bottle table lamp

This option for designing a light source is very common, since making a table lamp from a bottle is much easier than it seems at first glance.

The bottle can act as an excellent base for a table lamp or stand alone lighting device without the addition of a lampshade. This is especially true if you have a bottle or jar in stock original form or colors.

A DIY bottle lamp can have 2 light connection options:

external - the cord and light bulb socket are attached to the outside of the bottle;
internal - the cord is threaded through the bottle.

In the second option of creating a table lamp from a bottle, you must first make a hole in the bottom so that the bottle does not burst. To do this, you need to bury it in a bucket of sand with the neck down, leaving about 5 cm above the sand. You need to pour a small puddle of water at the bottom. Using a diamond drill, you need to drill a hole in the center of the bottle, holding the drill strictly vertically. A similar hole needs to be made in the bottle cap. Now you can design a table lamp for your desk, bedside table or window sill.

Lampshades for table lamps

To create a lampshade for a table lamp with your own hands, you don’t have to be a designer or decorator. There are a huge number of options for decorating lamps, among which everyone will find something suitable not only for their taste, but also for their abilities. Several ways to make a lampshade for a table lamp from scrap items:

Decoupage technique. Breathe new life You can use an old lamp or update a piece of furniture using the long-known decoupage technique. Thanks to decoupage, any old thing It will look like it came from a store shelf. You just need to find beautiful napkins for decoration that fit into the interior and not deviate from the rules of decoupage.
Fabric lampshades. These types of lamps fit well into country and Provence interior styles. You can update an old lampshade with bright fabric, or you can create a completely new one on a frame made of wire, for example, and scraps. P6
Volumetric flowers and decorations are perfect for romanticism or Moroccan style. You can create decorative elements in the form of flowers from napkins, ribbons, threads, and fabric.
Embroidery on the lampshade. You can use beads, large beads, sequins.
Mosaic from any flat objects or glass.
The ombre effect is a sign of minimalism. It is enough to stretch the painted fabric onto the frame in two colors that smoothly fade into each other.

Several ways to create a table lamp for a doll

Often girls ask their parents for additions to their favorite doll in the form of pieces of furniture, clothing, and accessories. It is not necessary to immediately refuse your child’s request if you do not have enough cash. After all, knowing, for example, how to make a table lamp for dolls, you can please your daughter and come up with an interesting activity for her for a while.

Examples of creating doll table lamps:

To make it you will need: a bottle cap, an old unnecessary corrector with a brush, paint of the desired color, an awl, glue. It's hard to imagine how to make a table lamp for dolls from all these items. But this is only at first glance. First you need to cut off the corrector brush, leaving the cap with the stick and wash them thoroughly. Then, using an awl, you need to make a hole in the bottle cap clearly in the middle. All that remains is to place the stick with the corrector cap on the glue in the hole in the lid and paint the base in the chosen color.
In the second option, the base of the lamp will be a button, the frame will be beads strung on a toothpick, and the lampshade will be cut bottom part bottles of drinking yoghurt. The parts are put on in the following order: button→glue→bead→toothpick→5-6 beads→lampshade→glue→bead.

Options for creating wooden table lamps

Increasingly in design modern interiors preference is given natural materials and eco-style. The lamps are not far behind. There are a huge number of wooden table lamps, but it is much more pleasant to create decor for your interior yourself, especially if you have interesting ideas and woodworking skills.

Very simple and original way create a lamp - use a log and LED light bulbs in a strip. A small log needs to be sawn into round, uniform layers and a small hole for the base must be made in the center of each. A tube with LED strip, and the layers of logs themselves are located above each other at a distance through which light will penetrate.

If you know how to use a jigsaw or electric saw well, you can create any figure, object or character outline from a decent part of a log. All that remains is to sand the base, run the cord, insert the light bulb into the socket and, if desired, make a lampshade.

An even simpler way to create an elegant eco-lamp is to collect sticks of the same size and attach them straight or diagonally to the old lamp frame. The lampshade can also be updated if desired.