Waterproofing film type yutakon characteristics. Anti-condensation films. Superdiffusion membrane yutavek

YUTAVEK - under-roof superdiffusion membrane

Function . The super-diffusion membrane YUTAVEK is used as a vapor-permeable under-roof waterproofing to protect under-roof structures, thermal insulation and the attic from humidity resulting from rain and snow, as well as from dust, soot and the adverse effects of wind. Thanks to high vapor permeability YUTAVEK increases weatherability water vapor from the internal space of the object. YUTAVEK can be used in construction with any type of thermal insulation and for all types of roofing and wall structures.

Specification .The YUTAVEK superdiffusion membrane is a three-layer polypropylene material consisting of two outer layers (black and white) that provide strength, and an inner layer that provides waterproofing ability. This material has high vapor permeability(1000 g/m2/24h). The roll has dimensions of 1.5 x 50 m and a density of 150 g/m2.

Usage .The YUTAVEK superdiffusion membrane is mounted directly on thermal insulation or other base covering load-bearing structure roofs, where the membrane comes into contact with its lower white side with the thermal insulation. This material can also be used for external insulation vertical walls of the object. The YUTAVEK superdiffusion membrane is recommended for all types of coatings. YUTAVEK should be stored indoors without access to ultraviolet (UV) rays.

YUTAKON - under-roof waterproofing with anti-condensation layer

Function . Under-roofanti-condensation YUTAKON waterproofing is a material for protection against the penetration of moisture from the outside into the internal structure of an object, as well as against soot and dust in ventilated sloping roof systems. At the same time, YUTAKON waterproofing prevents the flow of condensing water vapor onto the applied thermal insulation due to the use moisture-absorbing non-woven material (viscose).

Specification .Four-layer waterproofing film YUTAKON - UV-resistant polypropylene fabric laminated on both sides with polypropylene film, to one side of which is attached moisture-absorbing non-woven material. Upper and bottom lamination provides waterproofing properties and vapor tightness of this film. YUTAKON polypropylene waterproofing fabric provides high strength, and the non-woven material absorbs water vapor generated in the internal space of the object. Once the condensation conditions disappear, the nonwoven material dries quickly in the air stream. Waterproofing YUTAKON has a width of 1.3 and 1.5 m with a length of 50 m and a density of 130, 140 g/m2. YUTAKON film, thanks to the raw materials included in its composition, has a long service life, no less than that of the roofing used. In addition, it is not susceptible to rotting, mold, pests, and does not negatively affect health.

Usage . The advantage of YUTAKON waterproofing is its strength and high ultraviolet stability (12 months), meaning that the roof can remain uncovered after covering with film for a long time unlike other roofing films. It can be used for protection roofing structures during production preparatory work before installing the roofing, as well as for temporary protection of thermal insulation from atmospheric influences. Thanks to the fact that this film YUTAKON is vapor-tight and prevents water vapor from penetrating from the internal space of the object into the roofing covering; it reduces the possibility of water vapor condensation on the roofing covering used. Although YUTAKON waterproofing film can be used for all ventilated sloped roofs, it is recommended to use it mainly for profiled roofing ( metal tiles) such as Gasell Profil, Rannila, Kami, Plegel, etc.

YUTAFOL D - under-roof diffusion waterproofing

Function . YUTAFOL D waterproofing serves as a vapor-permeable under-roofing film to protect under-roof spaces from dust, soot and moisture arising from rain and snow, and in attic spaces protects thermal insulation from external moisture and at the same time creates the possibility, thanks to microperforation, ventilate water vapor. Waterproofing UTAFOL D is intended only for ventilated sloping roof systems, as well as for waterproofing wall structures when installing a film between the main load-bearing wall and siding.

Specification . Waterproofing films UTAFOL D Standard and UTAFOL D Special consist of three layers: the main one is a reinforcing mesh made of polyethylene strips; and two external ones, made of polyethylene film. Reinforcement mesh waterproofingUTAFOL D imparts strength to the material, double-sided lamination provides waterproofing properties, and microperforation creates an opportunity vapor permeability. This group also includes UTAFOL D Silver film. On the surface of some films, approximately 12 cm from the edge, there is a colored stripe, indicating a vapor-permeable version of the film. In addition, the color bar determines the recommended horizontal surface overlap with subsequent film sheet UTAFOL D . More precise information regarding overlap is given in the table.Waterproofing UTAFOL Dis wound onto a roll so that it can be easily rolled out on the roof.

The exception is the waterproofing film UTAFOL D Silver. It has a width of 1.4 and 1.5 meters with a length of 50 m and different densities- from 96 to 220 g/m2. The film, thanks to the raw materials included in its composition, has a long service life. In addition, it is not susceptible to rotting, mold, pests and does not negatively affect health.

Usage . YUTAFOL D waterproofing films can be used for all types of roofs ( ceramic tiles, cement-sand tiles, flexible tiles, metal tiles, euro slate, etc.), as well as for siding. The film should be stored away from UV rays.In case of fire, it does not support the fire, as it contains a self-extinguishing reagent.

YUTAFOL SP 1 - connecting tape

Functions . Connecting tape UTAFOL SP 1 provides air - vapor tightness connecting films with vertical and horizontal overlap, used for attaching to protruding parts. For example, in case smooth surface it is used to attach to adjacent building structures. Thanks to butyl rubber and its perfect properties, the connecting tape YUTAFOL SP 1 makes it possible not only to perfectly attach films and other materials to each other, but also guarantees the strength of the connections against the penetration of water vapor.

Specification . Connecting tape YUTAFOL SP 1 is a double-sided self-adhesive connecting tape made of butyl rubber without reinforcement, dimensions 1x15 mm, wound on a paper sleeve of 45 m.p.

Application . Can be used to connect polyethylene and polypropylene materials, these materials with others, such as metal, glass, wood, etc. subject to cleanliness and degreasing of surfaces.

The problem of getting wet thermal insulation materials is relevant for any specialist in the construction field. This is due to the fact that under the influence of moisture it not only loses its functionality, but will also require replacement after repeated wetness. It will help to cope with this problem anti-condensation film. It can become a reliable barrier to moisture in the under-roof space and can be used both during the construction process and during repair work.

Features of the material

Anti-condensation waterproofing film made from a material such as polypropylene. Non-woven textiles are applied to one side of it, the pile of which effectively retains water. The mass of retained moisture can be several times greater than the mass of the film itself. At the same time, it itself will effectively prevent rain and snow from blowing in from the street, and will also increase the functionality of any roof because:

not afraid of exposure to ultraviolet rays;
prevents the transmission of heat from inside to outside;
has decent strength characteristics;
will serve for a long time;
You will be pleased with the ease of installation.

Thus, thanks to the use waterproofing under-roof anti-condensation film, any roof will become even more functional and durable!

When are they used?

Anti-condensation waterproofing films are used when a conventional diffuse membrane cannot cope with the functions assigned to it. These functions are to provide layer protection thermal insulation material from the destructive effects of condensation and ensure effective removal of moisture. Thus, anti-condensation film for metal tiles(and others finishing materials) is universal material, which can be used in a number of cases. For example, for arranging an uninsulated under-roof space or for waterproofing a roof located above a room with high level humidity. Another advantage of using this material is its ability to remove moisture from those rooms in which the so-called “wet” technology was used for finishing. Their use will also be advisable during the construction of the roof before finishing work. In this case, they will provide protection for the thermal insulation layer from the destructive effects of ultraviolet rays. This became possible due to the fact that the film itself does not collapse under their influence. It is worth noting that despite additional costs on the purchase and installation of this material, you can achieve savings of almost 50% by extending the service life of the roof.

The fact that insulation moistened with condensate loses almost half its ability to retain heat is known to any specialist in the construction industry. This problem is especially relevant for the under-roof space. In order to eliminate this negative factor, it is necessary anti-condensation film. It provides the necessary protection of the insulation from moisture penetration. And today this task is one of the most important when constructing new houses or renovating old ones. That's why anti-condensation waterproofing films are one of the most popular products in the global construction market.

What is anti-condensation film?

Under-roof anti-condensation waterproofing film is a product made of polypropylene, on one side of which non-woven textiles are applied. Its presence is quite justified, since textile pile has the property of retaining moisture, and its weight can be several times greater than the weight of the film itself.

Polypropylene from which they are made anti-condensation films for metal tiles, is an effective barrier to moisture. It does not allow air to pass through, thereby preventing snow and rain from blowing in from the outside. In addition, it has other characteristics that make any roof more functional, namely:

insensitive to ultraviolet radiation;
does not allow heat to pass out;
has excellent strength characteristics;
easy to install.

Features of application

Anti-condensation films - best option for those cases in which diffuse membranes are not able to provide the necessary protection of the insulation from the negative effects of condensation and cannot provide the desired moisture removal. They are ideal for the following cases:

arrangement and repair of the attic;
installation of roofs finished with euro slate, metal tiles, corrugated sheets;
arrangement of uninsulated under-roof space;
installation of roofs over rooms with high humidity levels.

In addition, do not forget that this type material is able to remove moisture well from the premises in which finishing work using “wet” technology. Due to their immunity to ultraviolet radiation, anti-condensation films can serve as temporary protection for the thermal insulation layer at the stage of roof construction when the finishing has not yet been installed.

In general, the presence of an anti-condensation film can extend the service life of a metal tile roof by more than 50%.

Anti-condensation film, Full waterproofing under-roofing anti-condensation film for metal tiles

Under-roof anti-condensation waterproofing film is a product made of polypropylene, on one side of which non-woven textile is applied.

What are anti-condensation membranes

Anti-condensation membranes (films) are coatings made of waterproof spraying and polypropylene fabric (used as an adsorbent layer) that do not allow steam to pass through. This combination absorbs steam and removes it beyond the roofing material. The film is capable of trapping condensation that forms on inside roof and protects the supporting structure. The pile after installing the film can hold condensate weighing 3-6 times its own weight.

The top layer is responsible for the water-repellent properties of the material, and the absorbent capabilities of the adsorbent layer prevent the passage of water vapor. This ensures insulation of the insulation and prevents condensation from entering the parts from the surface of the membrane rafter system.

Where are anti-condensation films used?

The main area of application of membranes is pitched metal roofs, namely: metal tiles, seam roofing coverings. They are in greatest need reliable protection from corrosion. Due to the low quality of the material, violation of technology, and exposure to temperature, microcracks may appear as a result of expansion or contraction of the metal during daily temperature fluctuations. The presence of condensation on the inside of the material leads to the formation of rust. Using an anti-condensation membrane is a way to eliminate the problems described above, since the adsorbent layer effectively absorbs steam and condensate.

Anti-condensation films with hydrophobic coating used where diffusion membranes cannot cope with the protection of the roof from condensation and drainage excess moisture. Anti-condensation products are perfect for insulating insulation, repairing attics, installing roofs covered with metal tiles, galvanized sheets, ondulin or corrugated sheets. In a roof that does not have insulation, anti-condensation films prevent the entry of dust and soot.

Films function perfectly in roofs that are located above objects with increased circulation humid air, and UV resistance allows membranes to be laid as temporary protection for rafters and insulation in the absence of finishing materials. Metal tiles, which have an anti-condensation film underneath, last 50-70% longer than a roof not protected by a membrane.

Advantages of anti-condensation film

high mechanical strength;
unlike roofing felt and glassine, it does not emit harmful substances when heated, it has no odor;
films are environmentally friendly and do not interact with acids and alkalis;
retains its properties throughout its entire service life, does not break or deteriorate under the influence of the environment;
thanks to UV stabilizers, the membranes can be used in the open sun without consequences;
Due to their light weight, the films do not load the rafter system, are easy and quick to install, and have reasonable prices.

Resistance to ultraviolet radiation, elimination of heat loss, resistance to stretching during installation are the main advantages of anti-condensation films.

Features of membrane installation

Anti-condensation films are installed between the insulation and the finishing or roofing material. The pile side of the membrane perfectly absorbs moisture and prevents it from getting onto inner surface roofs. During installation, it is necessary to provide powerful ventilation of the under-roof space for unimpeded escape of moisture. For this purpose it is done ventilation gap in the rafter system.

Membranes are installed only in dry weather after installing the rafter system and laying insulation. The film is laid out evenly, without folds, with the absorbent surface down on the rafters, and the bottom should not come into contact with the heat-insulating material. It is laid out only overlapping and in horizontal stripes from the eaves to the ridge of the roof.

Fastened with a construction stapler or galvanized nails with a large head. The overlap of the strips vertically should be 20 cm, and horizontally - at least 15 cm. The membrane joints are laid on the rafters and secured together with mounting tape. The distance between the anti-condensation film and the insulation should be 40-60 mm; moisture will flow along the lower edge of the membrane into the gutter for water drainage.

After installation, the covering is secured using 3x5 cm slats and nailed with galvanized nails on top of the rafters. A sheathing is made on top of the slats. After installation is completed, moisture should not get on the insulation. Places of contact of the anti-condensation membrane with stove and fireplace chimneys, antenna stands and ventilation ducts should be further insulated.

Ondutis is a popular manufacturer of anti-condensation films

Ondutis anti-condensation membranes are very popular, namely: R70, which protects the insulation from steam and condensation, and R70 Smart - comes complete with mounting tapes for gluing.

Conclusion

When choosing a film, you need to pay attention to its vapor permeability: it should be close to zero (0.25-0.35 g/m2 h*Pa) in order for the membrane to maximally protect the roof from condensation and subsequent corrosion.

Anti-condensation membranes (films): What is it?

We will understand what anti-condensation membranes or films are in this article from construction experts.

Under-roof waterproofing film

Roofing films provide excellent vapor and waterproofing!

Anti-condensation roofing films: main characteristics

Each of us, having a house or cottage, is interested in ensuring that condensation does not form under the roof of the home and that the structure can last as long as possible. After all, what causes condensation? It appears due to temperature changes on the lower plane of metal sheets.

In addition to this, the vapors rising from interior rooms buildings, in the cool air the spaces under the roof turn into water. And this is already fraught with the insulation getting wet, which means it will lose its thermal properties. This is also a direct path to freezing of the roof and the appearance of ice on it, rotting of the sheathing and rafters, an increase in mold and damage interior walls and ceilings of the house.

To avoid such unforeseen situations, it is better to take care in advance of both the insulation of the required thickness and its protection from the metal tiles - a correctly selected under-roofing film will help 100% avoid problems with the roof!

Vapor and waterproofing - what types of films can provide them? It should be noted that hydro- and vapor barrier films can be: single-layer and consist of several layers, with or without adhesive tape... That is, roofing films can always be chosen to suit every taste, at any cost and taking into account all the nuances proper organization space under the roof (i.e., high-quality film must be water- and airtight, vapor-permeable, durable, and so on).

So, a waterproofing film of any type is designed to prevent moisture from leaking in from the outside and at the same time should help remove a certain amount of insulating vapor to the outside (due to microperforation).

Installation of films must be done with a sag of 20 mm (above the insulation).

As for vapor barrier films, they are needed to protect the insulation from steam. There must be a tight connection!

Under-roofing anti-condensation films: the most common of them

Tyvek® Soft membrane

A single-layer material with which vapor barrier can be easily achieved. Is excellent protection pitched roof with a ventilated gap (even attic) from all winds and precipitation. Used for work and residential premises.

Single-layer waterproofing film with increased strength and anti-reflective coating. Perfectly protects stingrays even mansard roofs+ walls of houses from winds and precipitation.

Its installation is carried out directly on the thermal insulation material and rafters without a ventilation gap.

Tyvek® Supro membrane

An excellent material when waterproofing and the highest strength with vapor permeability are required. In addition, the film does an excellent job of providing wind protection for slopes of any variation (warm, cold or combined roofs). It is successfully used in floor and wall structures.

A film with pronounced waterproofing properties. It has adhesive tape of the highest strength and is equipped with a vapor barrier.

Most best option to protect the roof space and walls of the building from all weather conditions. It is used in all types of roofs, both with and without load-bearing structures.

Tyvek® Housewrap

This under-roof film can be laid directly on the thermal insulation. It is a durable, lightweight, flexible, windproof, single-layer material with waterproofing properties. It is good because it increases the tightness of the structure and can be fixed to frame rack, plywood sheathing, block masonry.

Ideal for wood and steel frames, curtain facades and concrete structures. Very durable (4 months without covering is not the limit).

DuPont™ Tyvek® Solid

The material is endowed with the highest characteristics, in particular it has excellent vapor barrier. Acts as a protector of various roofs and facades from wind gusts and other weather conditions. It has an anti-reflective coating and can be laid directly on thermal insulation and rafters. Suitable for both commercial and individual homes.

Tyvek® Solid Silver

It perfectly saves energy at home, provides warmth in winter, and cool comfort in summer. Allows you to save on heating and air conditioning up to 15-20%.

DuPont™ Tyvek® Supro Tape membrane

Durable hydro/vapor barrier film with adhesive tape highest quality. Excellently protects roof slopes of various load-bearing or non-load-bearing structures from winds and various precipitation.

Indispensable for the construction of roofs of both non-residential and residential buildings.

DuPont™ AirGuard® Reflective

The most advantageous offer for those consumers who want to achieve thermal resistance the entire room, due to the reflection of thermal radiation inside the home. Vapor barrier layer makes it possible to enhance the effect of thermal insulation and makes the building more energy efficient.

Tyvek AirGuard® Reflective

Moisture resistance, tightness, fur. strength, low condensation formation, low heat loss during convection - this is all the vapor barrier film of the specified model. In addition, it does not respond to fire and meets all international standards as rubber-based materials and plastics. Able to reflect about 95% of warm radiation.

Tyvek AirGuard® SD5

The modern building membrane is an excellent choice when you need to reduce heat losses and minimize the formation of condensation inside the thermal insulation material. Lightweight, easy to install, with mechanical strength, control of steam transmission, and full compliance with the European standard certificate (EN 13984), the film is very popular in all corners of the Russian Federation.

Because its main advantages: the absence of a “greenhouse” effect, a comfortable humidity-temperature balance in the house, environmental friendliness and safety for the outside world.

Diffusion type waterproofing filmDELTA-VENT N and DELTA-VENT N PLUS

3-layer film is excellent for completely insulated roofs and is a fabric made of non-woven material on a PVC base (the layers are glued together with ultrasound). Features self-adhesive edges for quick, wind- and waterproof installation (no need for tape or glue).

This under-roofing film has a gray surface with a matte effect, low weight (130 g/m2), and the highest resistance to fur. damage and data stability.

2-layer premium film with an anti-condensation layer that retains and then removes condensation due to diffusion. Is the guarantor of such important feature as waterproofing. Resistant to tearing and steam penetration (this is facilitated by the polyurethane coating).

When laying it is convenient because it has on its underside non-woven material and a cellular surface - during cutting, smooth edges come out and the blade is wasted minimally. Widely used in roofs without decking or with formwork.

4-layer fabric with a reflective layer of aluminum, belongs to the premium class. Used on flat and pitched roofs.

During its operation, you will achieve complete vapor barrier; also, such a film helps save energy.

The film is endowed with record strength properties, the highest ductility, improved thermal protection and 99% electromagnetic shielding. radiation.

Tyvek® roofing films and acrylic tapes

Tyvek® acrylic tapes come in both single-sided and double-sided. 1-sided tapes are good for sealing overlaps, are excellent for many membranes, and as a sealant cope well with joints at the junction of doors, windows, and pipes.

Double-sided tapes have more capabilities: they have excellent adhesion in humid conditions, are suitable for all membranes, which can be glued both to each other and to smooth surfaces.

Under-roof waterproofing anti-condensation film - review of materials, MY ROOF

Under-roof waterproofing film for MY ROOF | Roofing films provide excellent vapor and waterproofing! Roofing films…

What is anti-condensation film?

insensitive to ultraviolet radiation;
does not allow heat to pass out;
has excellent strength characteristics;
easy to install.

Features of application

Anti-condensation films are the best option for those cases in which diffuse membranes are not able to provide the necessary protection of insulation from the negative effects of condensation and cannot provide the desired moisture removal. They are ideal for the following cases:

arrangement and repair of the attic;
installation of roofs finished with euro slate, metal tiles, corrugated sheets;
arrangement of uninsulated under-roof space;
installation of roofs over rooms with high humidity levels.

In addition, we should not forget that this type of material is capable of removing moisture well from rooms in which finishing work was carried out using “wet” technology. Due to their immunity to ultraviolet radiation, anti-condensation films can serve as temporary protection for the thermal insulation layer at the stage of roof construction when the finishing has not yet been installed.