The majority of people are convinced that energy for existence can only be obtained from gas, coal or oil. The atom is quite dangerous; the construction of hydroelectric power plants is a very labor-intensive and costly process. Scientists around the world say that natural fuel reserves may soon run out. What to do, where is the way out? Are humanity's days numbered?
All from nothing
Research on the types of “green energy” has recently been carried out more and more intensively, as this is the way to the future. Our planet initially has everything for human life. You just need to be able to take it and use it for good. Do many scientists and amateurs create such devices? as a generator of free energy. With their own hands, following the laws of physics and their own logic, they do something that will benefit all of humanity.
So what phenomena are we talking about? Here are a few of them:
- static or radiant natural electricity;
- use of permanent and neodymium magnets;
- obtaining heat from mechanical heaters;
- transformation of earth's energy and;
- implosion vortex engines;
- solar thermal pumps.
Each of these technologies uses a minimal initial pulse to release more energy.
Free energy with your own hands? To do this you need to have a strong desire to change your life, a lot of patience, diligence, a little knowledge and, of course, necessary tools and components.
Water instead of gasoline? What nonsense!
An engine running on alcohol will probably find more understanding than the idea of the decomposition of water into oxygen and hydrogen molecules. After all, even in school textbooks it is said that this is a completely unprofitable way to obtain energy. However, there are already installations for hydrogen separation using ultra-efficient electrolysis. Moreover, the cost of the resulting gas is equal to the cost of cubic meters of water used in this process. It is equally important that electricity costs are also minimal.
Most likely, in the near future, along with electric vehicles, cars whose engines will run on hydrogen fuel will be driving along the roads of the world. An ultra-efficient electrolysis plant is not exactly a free energy generator. It is quite difficult to assemble it with your own hands. However, the method of continuous hydrogen production using this technology can be combined with methods for producing green energy, which will increase the overall efficiency of the process.
One of the undeservedly forgotten
Such devices do not require any maintenance at all. They are absolutely silent and do not pollute the atmosphere. One of the most famous developments in the field of environmental technologies is the principle of obtaining current from the ether according to the theory of N. Tesla. The device, consisting of two resonantly tuned transformer coils, is a grounded oscillatory circuit. Initially, Tesla made a free energy generator with his own hands for the purpose of transmitting radio signals over long distances.
If we consider the surface layers of the Earth as a huge capacitor, then we can imagine them in the form of a single current-conducting plate. The second element in this system is the ionosphere (atmosphere) of the planet, saturated with cosmic rays (the so-called ether). Electrical charges of opposite polarities constantly flow through both of these “plates.” To “collect” currents from near space, you need to make a free energy generator with your own hands. 2013 was one of the most productive years in this direction. Everyone wants to enjoy free electricity.
How to make a free energy generator with your own hands
The circuit of N. Tesla's single-phase resonant device consists of the following blocks:
- Two regular 12 V batteries.
- with electrolytic capacitors.
- A generator that sets the standard current frequency (50 Hz).
- Current amplifier block directed to the output transformer.
- Converter of low voltage (12 V) to high voltage (up to 3000 V).
- A conventional transformer with a winding ratio of 1:100.
- Voltage boost transformer with high-voltage winding and strip core, power up to 30 W.
- Main transformer without core, with double winding.
- Step-down transformer.
- Ferrite rod for system grounding.
All installation blocks are connected according to the laws of physics. The system is configured experimentally.
Is all this really true?
It may seem that this is absurd, because another year when they tried to create a free energy generator with their own hands was 2014. The circuit described above simply uses the battery charge, according to many experimenters. The following can be objected to this. Energy enters the closed circuit of the system from the electric field of the output coils, which receive it from the high-voltage transformer thanks to relative position. And the battery charge creates and maintains tension electric field. All other energy comes from the environment.
Fuel-free device for obtaining free electricity
It is known that the occurrence magnetic field in any engine contribute to conventional ones made of copper or aluminum wire. To compensate for the inevitable losses due to the resistance of these materials, the engine must operate continuously, using part of the generated energy to maintain its own field. This significantly reduces the efficiency of the device.
In a transformer powered by neodymium magnets, there are no self-induction coils, and therefore there are no losses associated with resistance. When using constant ones, they are generated by a rotor rotating in this field.
How to make a small free energy generator with your own hands
The scheme used is as follows:
- take the cooler (fan) from the computer;
- remove 4 transformer coils from it;
- replace with small neodymium magnets;
- orient them in the original directions of the coils;
- By changing the position of the magnets, you can control the rotation speed of the motor, which operates completely without electricity.
This almost retains its functionality until one of the magnets is removed from the circuit. By connecting a light bulb to the device, you can illuminate the room for free. If you take a more powerful motor and magnets, the system can power not only a light bulb, but also other household electrical appliances.
About the operating principle of Tariel Kapanadze’s installation
This famous do-it-yourself free energy generator (25 kW, 100 kW) was assembled according to the principle described by Nikolo Tesla back in the last century. This resonant system is capable of producing a voltage many times greater than the initial impulse. It is important to understand that this is not a “perpetual motion machine”, but a machine for generating electricity from natural sources, which are freely available.
To obtain a current of 50 Hz, 2 square-wave generators and power diodes are used. For grounding, a ferrite rod is used, which, in fact, closes the surface of the Earth to the charge of the atmosphere (ether, according to N. Tesla). Coaxial cable is used to supply high-power output voltage to the load.
Speaking in simple words, a DIY free energy generator (2014, circuit by T. Kapanadze), receives only the initial pulse from a 12 V source. The device is capable of constantly supplying standard electrical appliances, heaters, lighting, and so on with normal voltage current.
A self-assembled free energy generator with self-powering is designed to close the circuit. Some craftsmen use this method to recharge the battery, which gives the initial impulse to the system. For your own safety, it is important to take into account the fact that the system output voltage is high. If you forget about caution, you can get a severe electric shock. Since a 25kW DIY free energy generator can bring both benefit and danger.
Who needs all this?
Almost anyone familiar with the basic laws of physics from the school curriculum can make a free energy generator with their own hands. The power supply of your own home can be completely converted to environmentally friendly and affordable etheric energy. Using such technologies, transportation and production costs will be reduced. The atmosphere of our planet will become cleaner, the process of the “greenhouse effect” will stop.
In these turbulent times, power outages sometimes occur. Solar panels good option, but not on the eve of a cloudy and snowy winter - something better and more powerful is required here. Diesel generator also a good option, but noisy and requires maintenance costs. Then why not invent... a bicycle? With easily accessible parts, you can build enough powerful generator current that will charge a phone, laptop, or a powerful battery for emergency lighting at home. The bicycle itself, without wheels, will stand on wooden base, and the rotation of the pedals will be transmitted to the electric motor of the generator.
Bicycle generator
The installation of the bike is done as follows: the rear wheel of the bike will drive the DC motor through the fan belt, this motor is connected to the charge controller, the charge controller charges the lead acid batteries and the battery is connected to the inverter. And then you can connect any 220V device to the inverter output.
Generator Basic Materials
- Flat board base
- Bicycle frame with rear wheel
- 12V lead acid battery
- DC-AC inverter
- DC-DC charger
- 24 V DC electric motor
- Fan belt
- Wires, screws, and metal rod
First, let's attach the bike to a piece of thick plywood. Make sure you have enough space and attach the motor to the rear wheel via a pulley.
After installing the bike stand, the front wheel should sit firmly on the blocks. Next, remove the tire from the rear wheel. Attach the pulley for the engine. Attach the belt to the wheel and pulley. Make sure the engine provides maximum fan belt tension.
The engine here is used at 2800 rpm, while driving at a speed of 30 kilometers per hour will give only 250 rpm at the rear wheel. Thus, we choose a pulley with a diameter about ten times smaller than the wheel, so even leisurely pedaling can give us the required speed (10x increase). For practicality purposes, we chose the thickest belts that could fit into the wheel rim. Depending on what length you use, the motor can be mounted at different distances from the rear wheel.
Charger
The charge controller regulates the current flowing into the battery and prevents overcharging and discharging the battery. We will not provide a diagram - firstly, the site is full of them, and secondly, it all depends on your capabilities and preferences.
Adding a Zener Diode
It is important not to exceed the charging input voltage level more than the limit (in our case 24 V). You can add a powerful zener diode with a breakdown voltage of 24V, so that if the voltage gets higher, the zener diode will not allow excess voltage to go to the charger.
Battery
If we use a 12 V battery, then the charge controller is for a voltage of 12 V. The battery in the photo with a capacity of 18 A/h works great in this generator circuit and has a maximum charging current of 5 A.
Inverter
The current that comes out of the outlet is alternating current (AC). The inverter converts the battery's low DC voltage into high 220V AC so you can connect regular electrical appliances. When choosing an inverter, make sure it is capable of delivering the required output current and voltage. The inverter recommended in this project has a power of 500 watts.
Thus it becomes possible without the slightest additional expenses obtain a sufficiently powerful, environmentally friendly source of electricity, at least 12 or 220 volts, which will help in case of accidents on power lines during a storm or other natural disasters. And at the same time, the generator works like a regular exercise bike!
Local power grids are not always able to fully provide electricity to homes, especially when it comes to country dachas and mansions. Interruptions in the constant power supply or its complete absence forces people to look for electricity. One of these is to use - a device capable of converting and storing electricity, using for this the most unusual resources (energy, tides). Its operating principle is quite simple, which makes it possible to make an electric generator with your own hands. Maybe, homemade model will not be able to compete with its factory-assembled counterpart, but this is a great way to save more than 10,000 rubles. If we consider a homemade electric generator as a temporary alternative source of power supply, then it is quite possible to get by with a homemade one.
How to make an electric generator, what is required for this, as well as what nuances will have to be taken into account, we will find out further.
The desire to have an electric generator for your use is overshadowed by one nuisance - this is high cost of the unit. Whatever one may say, the lowest-power models have a fairly exorbitant cost - from 15,000 rubles and above. It is this fact that suggests self-created generator However, he himself the process can be difficult, If:
- no skill in working with tools and diagrams;
- there is no experience in creating such devices;
- the necessary parts and spare parts are not available.
If all this and a great desire are present, then you can try to build a generator, guided by the assembly instructions and the attached diagram.
It is no secret that a purchased electric generator will have a more expanded list of capabilities and functions, while a homemade one is capable of failing and malfunctioning at the most inopportune moments. Therefore, whether to buy or do it yourself is a purely individual question that requires a responsible approach.
How does an electric generator work?
The operating principle of an electric generator is based on the physical phenomenon of electromagnetic induction. A conductor passing through an artificially created electromagnetic field creates a pulse, which is converted into direct current.
The generator has an engine that is capable of generating electricity by burning a certain type of fuel in its compartments:, or. In turn, the fuel, entering the combustion chamber, produces gas during the combustion process, which rotates the crankshaft. The latter transmits an impulse to the driven shaft, which is already capable of providing a certain amount of output energy.
Very often, lovers of outdoor recreation do not want to give up amenities everyday life. Since most of these conveniences involve electricity, there is a need for an energy source that you can take with you. Some people buy an electric generator, while others decide to make a generator with their own hands. The task is not easy, but it is quite doable at home for anyone who has technical skills and the necessary equipment.
Selecting a generator type
Before you decide to make a homemade 220 V generator, you should think about the feasibility of such a decision. You need to weigh the pros and cons and determine what suits you best - a factory sample or a homemade one. Here main advantages of industrial devices:
- Reliability.
- High performance.
- Quality assurance and access to technical support.
- Safety.
However, industrial designs have one significant drawback - a very high price. Not everyone can afford such units, so It’s worth thinking about the advantages of homemade devices:
- Low price. Five times, and sometimes more, lower price compared to factory electric generators.
- Simplicity of the device and good knowledge of all components of the device, since everything was assembled by hand.
- The ability to modernize and improve the technical data of the generator to suit your needs.
A home-made electric generator is unlikely to be any different. high performance, but it is quite capable of providing minimal requests. Another disadvantage of homemade products is electrical safety.
It is not always highly reliable, unlike industrial designs. Therefore, you should take the choice of the type of generator very seriously. Not only savings will depend on this decision cash, but also life, the health of loved ones and oneself.
Design and operating principle
Electromagnetic induction underlies the operation of any generator that produces current. Anyone who remembers Faraday's law from the ninth grade physics course understands the principle of converting electromagnetic oscillations into direct electric current. It is also obvious that create favorable conditions supplying enough voltage is not that easy.
Any electric generator consists of two main parts. They may have different modifications, but are present in any design:
There are two main types of generators depending on the type of rotor rotation: asynchronous and synchronous. When choosing one of them, take into account the advantages and disadvantages of each. Most often the choice craftsmen falls on the first option. There are good reasons for this:
In connection with the above arguments, the most likely choice for self-made is asynchronous generator. All that remains is to find a suitable sample and a scheme for its manufacture.
Unit assembly procedure
First, you should equip your workplace with the necessary materials and tools. Workplace must comply with safety regulations when working with electrical appliances. The tools you will need are everything related to electrical equipment and vehicle maintenance. In fact, a well-equipped garage is quite suitable for creating your own generator. Here's what you'll need from the main parts:
Having collected necessary materials, begin to calculate the future power of the device. To do this, you need to perform three operations:
When the capacitors are soldered in place and the desired voltage is obtained at the output, the structure is assembled.
In this case, the increased electrical hazard of such objects should be taken into account. It is important to consider proper grounding of the generator and carefully insulate all connections. Not only the service life of the device, but also the health of those who use it depends on the fulfillment of these requirements.
Device made from a car engine
Using the diagram for assembling a device for generating current, many come up with their own incredible designs. For example, a bicycle or water-powered generator, windmill. However, there is an option that does not require special design skills.
Any car engine has an electric generator, which is most often in good working order, even if the engine itself has long been scrapped. Therefore, having disassembled the engine, you can use finished product for your own purposes.
Solving a problem with rotor rotation is much easier than thinking about how to make it again. You can simply restore a broken engine and use it as a generator. To do this, all unnecessary components and accessories are removed from the engine.
Wind dynamo
In places where the winds blow without stopping, restless inventors are haunted by the waste of nature's energy. Many of them decide to create a small wind farm. To do this, you need to take an electric motor and convert it into a generator. The sequence of actions will be as follows:
Having made his own windmill with a small electric generator or a generator from a car engine with his own hands, the owner can be calm during unforeseen disasters: there will always be electric light in his house. Even after going outdoors, he will be able to continue to enjoy the conveniences provided by electrical equipment.
I will show you how to assemble a simple, but quite powerful, 220 volt generator.
You will need:
- commutator motor, you can have another one for 12 volts- attachment to the motor axis - drill chuck
- UPS or inverter from 12 to 220
- 10 ampere diode: D214, D242, D215, D232, KD203, etc.
- wires
- bike
- and preferably a 12 volt battery
Assembly:
- secure the bike so that the rear wheel rotates freely, hang it up- screw the cartridge onto the motor axis
- fasten the motor so that the cartridge is pressed tightly against the wheel, you can tighten it with a spring
- connect the motor to the battery: the negative wire of the motor to the negative of the battery, the positive wire of the motor to the anode of the diode, the cathode of the diode to the positive of the battery
- connect the battery to an uninterruptible power supply or an inverter
All! You can connect 220 volt consumers to the uninterruptible power supply and use electricity! As soon as the battery is discharged, all you have to do is pedal and the battery will be charged in about an hour.
Where can I get the parts?
- the motor can be bought at a car store: cooling fan motor. It's not expensive. And if you want it for almost nothing, then you can twist it at a metal collection point from an old car.- uninterruptible power supply from a personal PC, maybe an old one with a bad internal battery. Or an inverter 12 - 220, sold in car stores.
- 10 ampere diode, for example: D305, D214, D242, D243, D245, D215, D232,
D246, D203, D233, KD210, KD203, etc. Sold in radio parts stores. Or you can unscrew it from old equipment.
My experience:
I used this generator for several months and it showed pretty good results! The battery charging current was approximately 10 amperes and depended on how you pedaled. If you turn it slowly, you get 5 amperes, if you turn it as quickly as possible, you get 20 amperes. The average generator power is 120 watts. Mainly used low power consumers:3 W - phone charging
- 5 W - radio receiver
- 7 W - charging and using the tablet
- 10 W - charging camera, flashlight and video camera
- 12 W - energy saving light bulb
- 30 W - music center
- 40 W - laptop
- 70 W - TV (rarely turned on)
I had enough charge for almost a day, after which I pedaled for an hour and I could use electricity again.
If anyone knows other methods for generating electricity at home, please share in the comments.
