Facade plaster Bolars

Application area
Facade plaster Bolars is a frost-resistant, weather-resistant plaster of increased strength, intended for finishing the facades of buildings and premises with any level of humidity. Possesses high vapor permeability, which makes it possible to “breathe” the surface. Easily leveled, does not crack, does not form shrinkage cracks. Made on a cement-sand base using highly effective modifying additives. For work at temperatures down to -10 0C, a winter, frost-resistant version is available.

Specifications

Name	Meaning
Color	Grey
Drying time	24 hours
Density of mortar mixture	1700-1750 kg/m3
Amount of water per 1 kg of dry mixture	0.20-0.23 l
Thickness of applied layer	2-20 mm
Adhesion	Not less than 0.5 MPa
Compressive strength	Not less than 10 MPa
Work temperature	+5°С+30°С
Operating temperature	-40°С+60°С
Frost resistance	At least 50 cycles
Consumption	13-14 kg/m2 (at 10 mm)
Maximum particle size	2 mm
Specific effective activity of NRN	Less than 370 Bq/kg, class 1

Recommended grounds
Bolars facade plaster is applied manually or using continuously operating plastering stations on all concrete, foam and aerated concrete blocks, gas silicate, brick, stone masonry, cement-sand plasters.

Preparing the base
The foundation must be strong and have sufficient load-bearing capacity. Peeling, weak areas must be removed. Before starting work, the surfaces must be dust-free and cleaned of all types of contaminants that reduce adhesion. finishing materials. Before starting work on plastering facades, external waterproofing must be carried out and drainage systems must be installed. engineering systems. Finishing of facades with defects storm systems not acceptable. It is recommended to treat bases with normal water absorption with BOLARS Strengthening primer. Highly absorbent substrates must be treated with BOLARS primer Deep penetration. Before applying the primer, areas affected by mold fungi are treated with the fungicidal composition BOLARS Anti-Mold. Plastering of surfaces is carried out after the soil has completely dried.

Preparation of the solution
In mechanized application, the mixture is prepared in mixing and feeding machines. plaster mortar. Pour facade plaster into the hopper plastering station. Adjust the water supply (the amount of water is determined by the type of plastering machine) to match the required consistency of the solution. To prepare the mortar mixture for manual application, you need to take a precisely measured amount of clean tap water at room temperature (0.20-0.23 l of water per 1 kg of dry water, 5.0-5.75 l of water per 1 25 kg bag). Mixing is carried out mechanically (with a drill with an attachment), evenly pouring the dry mixture into water until a homogeneous paste-like mass is obtained. Let the solution stand for 3-5 minutes, then stir again and it is ready for use. The finished solution is in working condition for at least 3 hours.

Execution of work
Treat the finished surface with the prepared solution of BOLARS Façade plaster using machine spraying or apply it with a trowel, trowel or spatula to the base in a layer of 2 to 20 mm, then level it using a rule or grater. When plastering brick walls and surfaces made of gas silicate blocks, it is recommended to use façade fiberglass mesh. To obtain an even, smooth layer, after the mixture begins to set on the wall, smooth the surface with a metal spatula. Application in two layers is allowed (total application thickness up to 30 mm). To do this, comb the first, not yet hardened, layer with a plaster comb and dry completely. Before applying the next layer, the surface must be treated with BOLARS Strengthening primer. For final leveling, it is recommended to use materials from the BOLARS putty group, depending on the type of base and work conditions.

Consumption
Average consumption Bolars facade plaster with a layer thickness of 10 mm 13-14 kg/m². 25 kg bag – 1.7-1.8 m² with a layer thickness of 10 mm.

Conditions of work
The specified time characteristics are valid at temperatures environment+20°C, relative air humidity 60%, may vary under other temperature and humidity conditions. When carrying out work and over the next 3 days, the temperature of the air and the base should be in the range from +5°C to +30°C. The temperature of the mortar mixture during the work must not be lower than +5°C. It is not allowed to apply plaster in rainy, windy weather, or in the presence of surface condensation. During the process of gaining strength, the plaster should be protected from drying out, drafts and direct sunlight.

Restrictions
To avoid reducing the strength characteristics of the plaster, it is prohibited to overfill water in excess of the norms specified by the manufacturer, and to additionally introduce other components into the finished mortar mixture. When the solution thickens in the working container, it is mixed a second time without adding water (within the viability time of the solution). When conducting interior work Adequate ventilation must be ensured. Forced drying of the plaster layer using heat guns is not allowed.

Precautionary measures
If the solution gets into your eyes, rinse them with plenty of water. It is recommended to carry out work with rubber gloves. KEEP AWAY FROM CHILDREN!

Packaging and storage
Bolars facade plaster is supplied in 25 kg craft bags

Plastered facade - perfect solution to protect walls from moisture and give them an aesthetic appearance. Products have proven themselves to be excellent Russian company Bolars. has a number of advantages and is in demand on the market finishing works.

What is Bolars Facade Plaster?

An effective composition for plastering facades. Contains special modifiers that prevent the appearance of microcracks on the surface. Imported polymer additives give the material excellent performance properties.

This coverage:

Frost-resistant;
Not afraid of exposure to moisture and natural factors;
Applies evenly;
Allows the surface to “breathe”;
Plastering work can be performed manually or mechanically;
Durable, proven well throughout its entire service life;
Not subject to shrinkage;
High adhesion;
Dries quite quickly.

Specifications

Application area

BOLARS facade plaster is used for coating High Quality during external and internal finishing works.

The composition performed well in rooms with normal and high humidity. The basis is acceptable:

Brick.
Stone.
Aerated concrete.
Concrete.

Preparation of façade mortar

The BOLARS composition is poured into a hopper, and then the mixture is prepared mechanically strictly according to the instructions for the plastering machine.

The viscosity of the solution is selected taking into account the characteristics specific type unit.

If the solution is prepared manually, the steps are as follows:

A kilogram of dry plaster is diluted clean water in the amount of 0.4l - 0.42l.
Water consumption per bag weighing 30 kg – 12 liters.
Add the mixture little by little to the water and stir gradually.
Using a drill with a special attachment or by hand, thoroughly mix the mass.
After 5-10 minutes, the aged solution is stirred a second time.
Can be plastered.

The solution is in working condition for no more than 3-4 hours.

Preparing the base

Check the strength of the base. The peeling parts are removed.
They carry out work on waterproofing and installation of drainage systems and utilities.
Clean the surface from dirt, dust, stains that reduce adhesion to the base.
The facade is treated with a suitable type of soil.
You can plaster façade surfaces after the primer has completely dried.

Application of facade plaster mixture

Video - :

Please note: the company produces Various types primers. The choice depends on the absorption capacity of the base:

BOLARS Strengthening – for normal water absorption.
BOLARS Deep penetration – for highly absorbent surfaces.
BOLARS façade Anti-mold with fungicidal properties – in case of mold damage.

Precautionary measures

Operations are performed with rubber gloves.
Make sure that the dry powder and solution do not get into your eyes.
If the solution gets on the cornea of the eye, you should quickly rinse your eyes with plenty of water.
If the condition worsens or discomfort appears in the eye, consult a doctor.
Keep bags and prepared solution out of the reach of children.

Price of façade Bolars

A kraft bag weighing 25 kg costs 250 rubles. It is enough for 18 sq. m, if the layer thickness is only 1 mm. The cost of material when changing the thickness of the coating is easy to calculate.

Protect your home from influence external environment and give it beautiful view possible in different ways.

But for lovers of the classics, using it is one of the most optimal options.

Moreover, the choice of compositions is construction market today is simply huge.

Among all the variety of finishing mixtures, it took its place and Russian manufacturer Bolars, whose products are enjoying some popularity today.

The material is a dry cement-sand mixture, which includes moisture-resistant components and modifiers that protect the coating from the formation of microcracks, as well as imported polymer additives that give the plaster high performance properties. It is used for finishing stone, concrete, aerated concrete and brick surfaces and forms a durable coating after drying.

The Bolars company has been producing building materials since 1999. In 2005, she entered the top three leaders of the central federal district Russia for the production of professional mixtures for repair and construction.

The advantages of the material include a number of qualities:

high moisture resistance. The finished finish is not afraid of exposure to precipitation and retains its appearance well;
the presence of special elastic components. These additives make the material frost-resistant and resistant to temperature changes. Temperature range at which the façade retains its performance characteristics, ranges from +50 to -60 degrees;
high adhesion and low fluidity ready mixture . When applied, the solution adheres well to the base and fills even minor cracks and holes on the surface;
vapor permeability. This property allows the coating to “breathe”;
the frozen mixture does not shrink;
plaster has self-leveling properties due to the presence of modifying additives in its composition. During the drying process, irregularities and scratches disappear from the surface of the coating.

Description of material

Any pronounced negative aspects material does not have. The properties that will be presented below relate more to the nuances of finishing work than to obvious shortcomings. And there are not many of them, only two:

during work, as well as over the next three days, the recommended temperature of the air and the base should be from +5 to +30 degrees. However, these restrictions do not apply to frost-resistant composition;
Do not apply the mixture during rain, wind or when there is condensation on the surface of the facade.

Technical characteristics and mixture consumption

Bolars facade plaster has the following parameters:

density frozen solution– 1550-1650 kg/m3;
the amount of water per 1 kg of dry composition is 0.2-0.23 l;
frost resistance – at least 50 cycles;
the time during which the finished mixture is suitable for use is 3 hours;
adhesion – from 4 MPa;
permissible layer thickness during application – from 3 to 20 mm;
vapor permeability - mg/mchPa;
consumption – 13-14 kg/m2 when applying the solution in a layer of 10 mm;
compressive strength – from 4 MPa;
complete drying time – 72 hours;
thermal conductivity - 0.4 W/mK.

NOTE!

The time parameters indicated above are valid at an air temperature of +20 degrees and atmospheric humidity of 60%. In other conditions, these indicators may vary.

How does Bolars plaster stand out from its competitors?

You can distinguish a product from other analogues through the advantages of the company itself. Manufacturer Bolars has many years of experience in the production of dry building mixtures and was able to gain fame not only in Russia, but also beyond its borders.

The presence of German production lines for the production and packaging of products allows the company to guarantee high quality products. In addition, the company has its own scientific laboratories, where the quality of raw materials and finished materials is determined, as well as laboratories where products are tested.

Bolars plaster meets the requirements of GOST ISO 9001-2008 and international standard ISO 9000 and has certificates of conformity state standard RF. The material is safe for health due to the use of natural raw materials without toxic additives in its production. The safety of the products is confirmed by hygienic certificates of the Ministry of Health of the Russian Federation.

Many color options

Types of Bolars plaster

You can find several varieties of dry mixtures of this brand on sale:

facade plaster. Used as a rough finish and suitable for both external and internal work. There are ordinary and frost-resistant (can be used at temperatures down to -10 degrees);
decorative plaster. Used to apply the finishing layer for internal and exterior decoration buildings. The finished coating imitates the structure of tree bark. The base color is white, but the surface can be painted when finishing facade paints. The basis of the material is white cement and marble chips with the addition of polymer and modifying components. Manufactured in 3 fractions: 1.5 mm, 2.5 mm, 3 mm;
block mixture. Used for thin-layer leveling of gas silicate, concrete, and plastered bases;
pebble. Intended for finishing facade and interior walls. The finished coating acquires a pebble texture;
thermal insulation plaster Bolars Easy Wall. It is used both for insulation of facades and interior walls, floors, coolants. Forms a base thermal insulation layer, onto which adhesive and decorative mixtures are subsequently applied. When applying a layer of 60 mm, it can replace finishing made of polystyrene foam boards and mineral wool.

Preparing the mixture

Ideally, a special plastering machine is used to mix the solution. The composition is poured into the hopper of the unit and mixed with water.

The viscosity of the mixture depends on the type of equipment used, therefore the mechanized method of preparing the solution requires compliance with the instructions included with the machine itself.

If such a device is not available, you can mix the solution using a construction mixer or drill with a special attachment.

The main thing here is to maintain the correct proportions and dilute the mixture with clean water.

The cooking process includes the following steps:

The dry composition is gradually added to the water and gradually mixed.
Stir the mass thoroughly until a homogeneous paste-like mixture is formed.
Allow the solution to stand for 5 minutes, after which it is thoroughly mixed again.
The material is ready - you can use it.

CAREFULLY!

You should not add the composition to the solution after it has been mixed for the first time and left to infuse. Otherwise, lumps will appear in the mixture, the presence of which will negatively affect the work process.

When mixing the solution, you should also take some precautions:

It is better to do all work with gloves;
It is necessary to avoid contact with the eyes of the dry or prepared mixture. If this does happen, you need to rinse your eyes with water;
If your condition worsens, you should immediately seek medical help.

As you can see, the process of preparing the solution is not complicated. And given the possibilities of choice, with the help of Bolars mixtures it is possible to carry out complex work on plastering the facade - from rough finishing to application.

Useful video

Video instructions for application decorative plaster on the wall:

In contact with

For interior and exterior use
On a cement-sand basis
Waterproof
Non-shrink
Frost-resistant

Description

Frost-resistant, weather-resistant, increased strength BOLARS "Facade plaster" is intended for finishing the facades of buildings and premises with any level of humidity. It has high vapor permeability, which allows the surface to “breathe”. Easily leveled, does not crack, does not form shrinkage cracks. Made on a cement-sand base using highly effective modifying additives. For work at temperatures down to -10 0C, a winter, frost-resistant version is available.

Instructions for use

Treat the finished surface with the prepared solution of BOLARS Façade plaster using machine spraying or apply it with a trowel, trowel or spatula to the base in a layer of 2 to 20 mm, then level it using a rule or grater. When plastering brick walls and surfaces made of gas silicate blocks, it is recommended to use facade fiberglass mesh.

To obtain an even, smooth layer, after the mixture begins to set on the wall, smooth the surface with a metal spatula. Application in two layers is allowed (total application thickness up to 30 mm). To do this, comb the first, not yet hardened, layer with a plaster comb and dry completely. Before applying the next layer, the surface must be treated with primer.

Consumption

The average consumption of facade plaster with a layer thickness of 10 mm is 13-14 kg/m². 25 kg bag – 1.7-1.8 m² with a layer thickness of 10 mm.

You can consider other options in a special section

Often, finding the right materials for construction or renovation requires a lot of time and unnecessary costs. Basically, you can buy and find building materials only by visiting many construction stores that are located in different areas cities. In Moscow, every year the construction of houses and renovations are becoming more and more in demand and necessary. Every day the need for large houses in the capital is becoming greater and greater, and with this the quantity required is also growing. building materials.

If you are planning to make repairs or start construction, then you simply need our website. Here you will find the answer to any question about construction, and you can also buy any construction materials from popular manufacturers in Russia. Navigation through the product catalog is very simple, all products are divided into appropriate categories.

For the company " Instroymaterial» selling building materials is not just about making a profit, but first and foremost about taking care of the client. In Moscow and the Moscow region, we sell building materials such as plaster, putty, metal and plastic mesh, waterproofing, grout, glue, cement and many other materials that are needed in construction and repair.

If you decide to start renovation or construction, you will still have to buy building materials, and the company Instroymaterial will help you with this. We offer a price list of building materials, which includes not only foreign, but also domestic manufacturers, some of them: Ceresit, MKU, Birss, Prospectors, Knauf, Bolars, Isover. Company Instroymaterial constantly updates its range of building materials.

Company " Instroymaterial» sells only high-quality products that will serve and protect your home or apartment for many years to come. Using our website, you can buy building materials without leaving your home or office. In this case, you do not have to waste a lot of time searching the required material. Our specialists will provide advice and help you make a profitable and correct purchase.

Company Instroymaterial works like with professional builders, and with clients who understand little about building materials. Our company is engaged in both retail and wholesale building materials.

But why do you need to choose our company to purchase building materials, because now there are many companies in this market that also sell building materials? The answer to this simple question is that our company works for clients, and we also provide big choice building materials, the range of which is expanding every day and is replenished with new products. We provide our clients affordable prices for construction materials. We offer only high quality building materials. On our website - catalog Instroymaterial, the most accurate and complete information about the product being sold is presented, which will allow you to make comparisons and choose the best option.

Our clients are commercial organizations, the shops, construction companies, small construction crews, and retail buyers. If you are interested in building materials in Moscow or the Moscow region, you can get detailed information about services, materials, discounts, working conditions and other information about building materials that are of interest to you on our website. After reading the information on the website, call the numbers in Moscow.

Let's sum it up by contacting our company Instroymaterial, to purchase building materials, you can save both money and time, and at the same time receive the goods from the best manufacturers High Quality.