How often, when we are at home, in the office or on the road, we cannot remember where we put our phone. To prevent this from happening, you should get comfortable and ergonomic stands that you can make yourself. A phone stand can be made with your own hands from the most unexpected materials at hand. Ours will tell you how to do this. step by step wizard Class.

How to make a phone stand with your own hands: options for the office and car

Whether at work or in the car, we all need to be connected at all times. At the same time, you don’t want to spend a lot of money on expensive stands, because they can be made from waste and used materials.

The simplest version of a phone holder is a card stand. To make it, you need to carefully bend the unnecessary plastic card in two places, as shown in the photo below, without allowing it to break.

Experience shows that a plastic card stand is very reliable and can even withstand air travel during severe turbulence.

To make a phone stand from paper clips or binders, as they are also called, you will need one large and one small clip. The legs of the small clamp should be placed between the holding part of the large clamp and the resulting structure should be placed on the table so that the clamp larger size rested on its surface.

Similar coasters can be made in five minutes from clothespins.

Paper clips make an excellent car stand. To make it, you need to disassemble a large clamp and slightly bend the metal parts, as shown in the photo below.

To avoid damaging the surface of the phone metal fastenings It is recommended to wrap the threads in several layers. We return the holders to their place, additionally securing them with adhesive tape and a rubber band. We attach the clip to the ventilation blinds. The phone is securely attached between metal parts binder.

Ordinary office paper, folded in a certain way, can even support the weight of a large smartphone. To make a paper stand, you need to measure the dimensions of the phone and adjust the pattern below to fit them.

Cut the piece out of paper, fold it along the dotted lines and insert the side parts into the slots. This design is good because it allows you to charge your phone without removing it from the stand.

We study popular options for stands for home comfort

A desktop phone stand for the home should not only be comfortable, but also durable, stylish and fit well into the interior of your home. Let's consider options for such products.

A phone stand made from newspaper tubes will be a wonderful gift and an excellent decoration for any interior.

To weave such a stand, you will need several pre-painted long newspaper tubes, scissors, knitting needles, a little glue and varnish.

We place six workpieces parallel to each other at a distance of approximately 1-1.5 cm and firmly fix them in the machine or any in a convenient way. We place knitting needles or wire in the outer racks to make it more convenient to form smooth and neat contours of the product. We begin to braid the base with a working tube using the rope technique or calico weaving. We monitor the parallelism of the rows and, if necessary, coat them with glue for better fixation.

We weave a rectangular piece of the required length. We take out the knitting needles or wire. The ends of the stands are carefully tucked in and trimmed. We give the workpiece the required curved shape, if necessary, wetting it a little with water.

Likewise we weave the leg of the stand on a smaller number of tubes. We bend the finished leg, install it on the main part and secure its posts between the rows of the stand. We cut off the excess and hide it. We coat the product with glue, if desired, additionally paint it and cover it with 1-2 layers of varnish. After complete drying, the stand can be used for its intended purpose.

Modular origami is a fairly young, but very popular type of needlework. With its help, you can make many unusual and original gizmos, including a phone stand from modules.

To make a stand you will need double-sided blue and pink color. We cut the sheets into blanks and fold the modules.

We start weaving from the base of the stand. It will require 28 blue modules, which must be connected to each other and closed in a ring. We make three more rows in the same way. From the fifth row we reduce the number of modules by 1, 2, 3, 4 pieces. In the seventh row we place one pink module in the middle.

In the eighth row we put 6 modules, make a skip, another 10 modules, skip, 6 modules. The number of pink modules is 2 pieces. In the next row, we place three pink modules on the pink area. We begin to design the shaped edging of the stand, as shown in the photo below.

In the back part we form a heart-shaped pattern, above which we install a number of blue modules. Gradually narrow the stand until a triangular wedge forms at its back.

The module stand is ready!

Video on the topic of the article

We invite you to watch the video tutorials below on how to make other options for phone stands.

The mobile phone has become an invariable attribute modern man. And on the road, at home, and on the desktop, a useful gadget is given the main place, otherwise “what if someone calls, but I don’t hear/see.” For convenient placement Cell phones on the table were invented by stands. You can buy them in the store, or you can make them yourself from scrap materials. Even the most useless at first glance “unnecessary garbage”, like cardboard packaging for dairy products or a long-used CD cover, can be useful in your work.

Cardboard stand

The first option is to make a mobile stand out of cardboard. This does not have to be a solid piece of material; you can take a used small-volume milk carton (0.5 ml). There is no need to glue anything: you only need scissors.

The box must be thoroughly washed, crumpled and the bottom cut off. Then cut it along the folds.

The work will require a central part in the shape of two rectangles. There is a fold between them. It needs to be cut and folded outside inward, pressing the bend with one hand.

Starting from the opposite end, from the bottom, you need to cut out a shape that resembles the letter “T”. It is narrowed at the top, but has a beveled corner.

When the figure is unfolded, the bottom edges become where the phone sits. It rests on the central edge. The budget stand is ready!

CD cover stand

Surely everyone has a couple of DVDs lying around their house. One of the unnecessary covers can be turned into a stand for your mobile phone.

To do this, the cover must be cut in half. Then cut off all the holes and rivets so that only a smooth rectangle with two curved corners at the ends remains.

The plate must be clamped with tweezers or pliers and placed in boiling water. This will make the plastic soft and pliable.

Holding the plate with pliers or any other tool, it must be bent so that one of the corner ends does not reach the other slightly. 2-3 cm is enough; the phone will be located in this space. One of the corners is glued to the surface. The result is an interesting and light stand. The device can be placed on it both vertically and horizontally!

Paper clip stand

Mobile phone stand made from paper clips – interesting thing, which can be done in 2 minutes. To do this, you need a large, massive paper clip, which you just need to straighten correctly!

To begin, the wire is completely straightened into a line. Then you need to pinch it and bend it again:

1. Bend in the shape of a tick - U.
2. Bend both ends at an angle of 90 ° C, starting approximately in the middle.
3. Bend the ends of each end slightly.

Thus, an ordinary paper clip turned into a laconic stand. The phone lies horizontally on it.

Stand made from toilet paper roll

As good as a sleeve from a used roll toilet paper, enough in every home! Don’t rush to throw away the cardboard form - it can be turned into a mobile phone stand in a matter of minutes.

All that is required is to correctly cut part of the sleeve at an angle. There should be a small piece of cardboard left in front to create a stop. Such a stand will not be able to accommodate a phone that is too tall, but standard size“fits” perfectly.

If desired, the stand can be decorated: painted, wrapped in fabric or covered with paper for gifts. And no one will believe that it was once part of a toilet roll.

Conclusion:

When working with familiar things, it is important to give free rein to your imagination: try it on, think, experiment. Then stands for mobile phones will appear in the house regularly - and always different and interesting!

Almost any thing can serve as a stand, and its uses can be countless. We provide you original options how to make a stand from any available materials that you may have at home.

For example, in everyday life you often need a stand for a tablet or smartphone; watching a movie, reading an article, or writing something without a stand for electronic gadgets is inconvenient.

It would seem that it would be better to buy a specialized case that will perform such a function, but sometimes it is needed here and now or you simply don’t want to spend money. So you need to use your wits and make such an invention with your own hands.

Materials for stands

What materials can the stand be made from?

• Cardboard
• Wire
• Fabric or foam
• Bottles
• Wooden products
• Paper sheets
• Constructor elements
• Plastic cards

Don't limit yourself to this list, turn on the imagination in your head and give any object such a function. The advantages of a stand that you can make with your own hands are speed of production, low cost, and uniqueness.

Pencils

Take 4 erasers for money and 6 regular pencils. Connect them together so that you get a three-dimensional triangle or pyramid.

Please note: inexpensive air conditioners with a guarantee in Sevastopol always available in the Klondike online store!

Paper clips

Using just one paperclip and half a minute of time will allow you to no longer have to hold your phone in your hands during another activity. You just need to bend the paper clip so that it holds the phone firmly when you place it on the resulting structure.

Plastic card

We make a stand with our own hands at home from an unnecessary plastic card. You just need to bend the card crosswise in two places so that you get the letter “S”. To do this, make a bend 1 cm from the edge, and a second one in the middle of the remaining plane. This stand will hold your phone firmly.

Cardboard tablet stand

There are more uses for cardboard than you would ever think of. You probably have an unnecessary piece of cardboard lying around somewhere at home. Fold the cardboard strip in half and draw a shape on it that you think will hold the phone if you unfold the cardboard and place your phone on it.

Experiment with the shape and you will realize that any shape will hold the phone securely. This stand is suitable not only for a phone; if you use a larger piece of cardboard, then a book or tablet can easily fit on such a stand.

Origami

There are many schemes on the Internet according to which you can fold a stand from a regular thick paper. A few movements with scissors and the stand will be ready. It can be folded to a small size and carried with you, and when you need it, just a couple of seconds and your phone is no longer in your hands.

Wire

The same as with a paper clip, you can do with wire. You'll get an excellent stand, only now it can even support a tablet.

For a more stable structure, you can use rubber bands, which will create elasticity and the stand will be more reliable.

LEGO parts

Do you have a child? Does he have LEGO toys? Take some cubes and make yourself a stand. This way you can create stands for the whole family and for any gadget, you just have to show your imagination.

Think about the idea of ​​what else you can make a stand for with your own hands. Another option for a holder for your phone can be an old cassette holder. This is a box, remember? It used to store cassette tapes. Just flip the cover all the way over and insert your phone into the cassette holder. Very convenient and compact.

Plastic bottle

It often happens that the socket is located quite high from the floor, and there are no cabinets or other furniture nearby where you could put your phone while it is charging. Shouldn't he be hanging on the wire, dangling from side to side?

You can take the unnecessary one plastic bottle, of course, empty and cut out of it a pocket with a hook, for which you can hang the bottle on the fork of your charger. No more holding your phone while it's charging.

Look at the photos of possible DIY stands and you will understand that there can be a thousand solutions.

The stand can be made from a block of wood, and you can give it the shape that you like best. You can even come up with a docking station that, when connected to it, will charge your phone. You just need to make a hole for the charger and insert the cable with the contact there.

Explore step by step instructions how to make a stand with your own hands in the form of a case. This way you will kill two birds with one stone – both the case and the stand.

If you are a creative person, then you will find the makings of a phone stand in any object. The main thing is the strength of the structure, because it will be very disappointing if your phone falls or breaks from the experimental stand. We hope that such a fate will not befall you.

Photos of do-it-yourself coasters

Modern means of communication perform many functions, so there is often a need to install a gadget on desk. The easiest way is to purchase a ready-made device at your local store, or you can make it yourself. There are many ways to make a phone stand from scrap materials and office supplies.

Related articles:

The most common material used to make phone stands is plastic. To make a smartphone holder with your own hands, you can use everything that is available in every home - paper clips and binders (clips), wire hangers for clothes, paper, wooden planks and even children's construction set. Self-made stands will not only be comfortable, but also original in their design and size.

There are several simple ways, thanks to which you can quickly create functional stands that are perfect for your gadget.

From stationery binders

Students and office workers are familiar with special clips for large stacks of papers, called binders. If you have holders, the easiest way is to make a phone stand with your own hands from them.

To do this, just connect 2 elements to each other, and bend 1 metal end towards the phone.

You can also fasten 2 binders using a piece of cardboard, and insert the smartphone into the plane between the metal ears. Despite its small size, such a device is capable of holding even a phone with a large screen diagonal both vertically and horizontally.

From Lego

If there are children living in the house, there will definitely be a plastic construction set with parts of different sizes and colors. There are no special instructions for making a phone stand; you just need to select the appropriate elements and connect them in any order. The main thing is that the design is stable and attractive.

From a paper clip

Of the many ways to make a shipment for a smartphone, the fastest and easiest is the one that uses a simple paper clip large size.

To make the device, you must first bend the clamp into a straight line. Then bend it again so that the middle part provides support for back wall, and the hook-shaped edges prevented the phone from sliding forward.

From a wire hanger

Subject to availability wire hanger for clothes can be made original stand for smartphone or tablet. All you need is pliers and a little patience:

1. First you need to bend both edges of the hanger so that they are located from each other at a distance equal to the width of the gadget. The edges are compressed with pliers until they are completely connected.
2. Make 2 folds at each end, about 3-4 cm in size.
3. At the next stage, the hook is bent at an angle of 90° and turned in the direction of the wings.
4. Then a hook is made at the end of the upper part, to which they hook internal element hangers and fix.

The design can be improved with rubber tubes, which will provide an anti-slip effect and make the product more attractive.

Shampoo bottle version

An empty shampoo bottle can be turned into a convenient and beautiful phone stand. The advantage of such a device is that it can be hung on the power supply of the charger and eliminate the risk of snagging the wires and dropping the gadget on the floor.

To make a holder you will need plastic container required size, marker and stationery knife. First, markings of future cutting locations are applied to the bottle, taking into account the depth of the phone, the location of the holes for the plugs and the dimensions of the power supply. After the layout is carefully drawn, all the lines are cut out with a knife and the edges are cleaned. If everything is done correctly, the holder can be easily placed on the charger plug and plugged into an outlet. The gadget itself will fit freely in the bowl, eliminating the bending of wires.

To make the device look more attractive, its surface can be covered with fabric or bright paper, and painted with paint suitable for plastic. The advantage of this stand is that it is inexpensive, since it uses discardable material. In addition, a wide selection is available color range and container sizes.

Popsicle stick version

Don't rush to throw away popsicle sticks. You can also make a beautiful phone stand out of them. Depending on the project, the design consists of several elements or includes a dozen components. You can glue the sticks with PVA or glue gun. After the holder is ready, it is recommended to paint or varnish it.

From paper

One of the most common materials used to make a DIY smartphone stand is paper or cardboard. If designed correctly, the product will be quite strong.

The easiest way is to create 2 triangular blocks different sizes. One will serve as the base, the other will support the bottom end of the phone. After the blanks are completely dry, they are fixed on 1 paper rectangle.

Homemade stand for a smartphone made of mahogany.

Hi all! Today we will do for mobile phone in the form of a dog - a symbol of the year.

Now you need to make a stand for it. To do this, we cut out a circle with a diameter of 70 mm from wood. Sand it with sandpaper.

We take several small gears like this.

We also take epoxy and hardener.

Take plasticine and apply thin layer on one side of the internal cavity of the figure and seal it with polyethylene on the same side.

Mix the epoxy glue according to the instructions and pour approximately 2 mm into the cavity of the figure. This will be the first layer. We are waiting for this layer to harden. Then we’ll lay out our pattern of gears and fill in the rest.

Our dog has dried up.

We remove the plasticine. We take some sandpaper and bring everything back to perfection.

Mark with a pencil the point on the figure where the hole will be.

Use a drill to make a small indentation.

Now we are making a wooden chopstick that will fix it all. We insert the chopstick into the stand, coat it with PVA glue and also bottom part figures in a thin layer so that the glue does not protrude. Let's connect. Leave until completely dry. Next, we rub our entire product with the herbalist’s impregnation.

This is what we got.