The walls of the second floor of the frame house are jagged. Posts in a frame wall. What does the absence of stabilizing elements or their incorrect installation lead to?

Reliability frame house, the degree of its resistance to wind, snow, and other adverse weather conditions, and the service life of such a structure are determined by the rigidity of its structure. The most popular method of strengthening the frame is installing jibs. Let's figure out whether it's worth spending your time and energy on installing jib bars or whether you can do without them.

What are jibs and what are they like?

Jib frames are additional components of a house frame that increase the reliability of the structure and increase the service life of the building. These elements are usually mounted at an angle of 45°, this indicator changes up to 60° if the jibs are installed next to door or window openings, as well as to wall junctions.

Most often, the jib is wooden beam, made from a board with a section of 25 by 100 mm. In most cases, this size is optimal and the use of larger frame strengthening elements is, as a rule, impractical. Jib beams with the mentioned cross-section strengthen the structure of the house, but do not weigh it down and do not create additional load on the foundation.

Jibs made of metal are also used. They are heavier and unpopular in Russia. In the USA, on the contrary, metal jibs are mostly found. The advantage of such jibs is their low price and high speed installations.

The disadvantage of these jibs in comparison with wooden ones is that the latter resist both compression and tension, while metal ones only resist tension. Therefore, when installing metal jibs, you have to place them crosswise for adequate resistance to the changing load vector. In addition, before installing metal components, it is necessary to carry out additional work on waterproofing.

Jibs can be installed either permanently or temporarily. The need to install temporary jibs arises if tiled wall cladding (OSB boards) has not yet been installed, however frame structure needs to be strengthened while this work is being carried out.

Why you can’t do without cuttings

The frame house itself is a fairly strong structure, but its structure also requires strengthening. The fact is that the frame components before installing the jib are located only parallel and perpendicular to each other. This arrangement of frame elements makes it unstable to ground displacements, wind and other “transverse” loads.

If the frame of the building does not have elements that provide rigidity, then such a house is at risk of losing the geometry of the structure, deformation, both external and interior decoration. It is possible that under the influence of serious lateral loads the house may “fold”.

The lack of frame rigidity leads to a decrease in the durability of the house structure as a whole. Not so radical, but quite unpleasant consequences of the lack of strengthening of the frame are heat losses due to the fact that the thermal insulation layer loses its integrity when the walls are displaced.

The result of incorrect distribution of jib beams and their insufficient quantity

So, the result correct installation jib is:

preventing vibrations and destruction of walls under the influence of weather factors;
no deformation of walls and internal partitions under loads;
increasing rigidity load-bearing structures;
more reliable fastening inside the walls thermal insulation materials;
ensuring uniform load distribution between frame elements.

After installing the jibs, the frame house building will successfully withstand strong winds, landslides and even earthquakes. Snow accumulated on the roof in winter time, will also not pose a threat to the integrity of the house.

Is it possible to refuse cuttings?

Lately, plywood sheathing or OSB (oriented strand board) have increasingly acted as jibs. The use of plywood is more justified, since it has a higher coefficient of spatial rigidity compared to chipboard and OSB.

However, even those frame houses that are sheathed with high-quality plywood, but lack jibs, often cannot withstand the impacts of the elements, although they are adapted for normal loads under normal conditions.

Jib beams can only be omitted during the construction of small frame structures that are not residential buildings, but have, for example, an economic purpose. Thus, frame garages, sheds or toilets can easily get by with sheathing without installing jibs, because due to small area load-bearing elements they are less susceptible to wind and other weather loads.

Consequences of hurricane winds

You should be aware that the casing must be made of strong material, supplied in the form of relatively large components. Finishing elements should be positioned similarly to the jibs - at an angle of 45°

Typical problems

In order for the jibs to truly perform their function efficiently and justify the financial and labor investments in their installation, you should strictly adhere to the basic rules for installing these structures.

Here are some installation secrets:

the jibs must be cut into the upper and lower horizontal frame frames and into the vertical posts - this is the only way the frame will become as rigid as possible;
installation of the jib from the inside is less convenient, but ensures a guaranteed absence of “cold bridges”;
when attaching the jib to frame elements You should use only nails, not self-tapping screws;
It is quite enough to install only two multi-directional jibs on one wall. Larger number reinforcing elements are unlikely to significantly increase the degree of rigidity of the frame;
installation must be done from the central part of the lower beam to the corners at the top. This installation order will ensure the formation of a right triangle between the stiffening elements and the corner post;
if the jibs are installed exclusively on the external walls of the structure, then most of the static load falls on them, and not on the internal partitions.

Remember: installation of jibs does not at all guarantee the protection of the house from external loads if the material of these elements is selected incorrectly or the installation process is carried out with errors.

Consequences of errors in material selection and installation:

the use of hollow jibs - their degree of wear resistance is low;
a similar problem occurs when choosing jibs with a small cross-section and, in general, low-quality lumber;
choice of strips or metal strips as jib for big houses— such reinforcing elements are more suitable for small buildings;
the use of poorly dried wood - after drying, gaps form in the areas of component connections and the rigidity of the structure decreases;
installing jibs in the corners is fraught with a decrease in the stability of the structure as a whole.

It is obvious that the use of jib - required condition strengthening a frame residential building. Structures in which such a solution was implemented will last a fairly long time, during which they will successfully withstand the elements and other loads. Thus, the jib will actually insure the owner against much greater losses than those associated with the manufacture and installation of these elements.

You need to know the main rule - installing the jib. The jib is an important, one of the main elements to ensure the rigidity and stability of the structure of your wooden house. Without this detail, the house will be shaky, easily exposed to the forces of nature, and its service life will be reduced tenfold.

Jibs: necessity or myth

There are popular opinions and “myths” about the need for mowing:
1. jibs are extra costs time and money during construction. So, people far from the construction business can argue. As stated earlier, the fundamental role of this structural element is its rigidity.
2. They can be replaced with external cladding. You can do without them if you are going to build a barn or other outbuilding. However, the exterior trim must be made of tile material or the finishing boards must be positioned at an angle of 45 degrees.
3. For interior walls(partitions) they can be neglected. In this case, the load perceived by the structure of the house from wind, snow on the roof and static load from the roof itself will be perceived only external walls. Partitions without jibs will undergo deformation, and the entire interior decoration will be damaged and cracks will appear.
4. Spacers are jibs. Developers often confuse struts with jibs. In construction, spacers are used when the height of the walls is 3 m or more. This is done to eliminate the “spring” effect of the board. But they do not give the house structure the necessary rigidity and stability in three-dimensional space.

Jib beams in a frame house are a necessity!

If you still doubt the installation of jibs when building a house and hope that they can be replaced with sheet sheathing or slabs (chipboard, OSB), then on the Internet you can find a lot of photographs of houses without jibs that refutes your hopes.

Let's look at the benefits of using jib beams when building a house:
Without the use of these parts, the frame and the entire house will not have sufficient reliability and durability.
Prevents deformation and damage to the external and internal decoration of the house.
Eliminates “walking” of inter-wall insulation.
Stabilizes the house and prevents it from folding.
Wind load, snow load and static load from the roof itself are distributed evenly throughout frame structure building.

Correct jibs

In the structure, it is important not only to provide for the presence of jibs, but also to properly manufacture and secure them:
1. The angle of installation of the jibs is 45 ° (ideal angle, ensures maximum structural rigidity). In places where there are door and window openings It is not always possible to maintain this angle. Therefore, an angle of 60° is allowed, and an increase in the angle is compensated by an increase in the number of jibs.
2. Do not use hollow jibs. An exception may be small one-story buildings with flexible diagonal connections.
3. Correctly install the jibs from the bottom from the center of the wall up to the ceiling of the vertical post with the top trim. At the top, the jibs should fit tightly (without gaps) to the edges of the racks and the upper ceiling.
4. When installing the jibs under them in vertical posts, it is necessary to make grooves for the jibs in the upper and lower trim. The depth of the groove is made depending on the thickness of the jibs. IN steel frame the jibs must go inside metal profile racks
5. The cross-sectional dimensions of the jib are calculated depending on the requirements of SNiP for each region separately.
6. Attach the corner stiffeners to each vertical post with two nails.

Mistakes that can be made when installing jib:

Using forests with unnatural humidity. As they dry further, the boards “shrink out” and gaps form in tight joints. The rigidity of the structure is significantly reduced.
The cross-sectional dimensions of the frame elements are smaller than those necessary to resist the loads.
Use of low-quality lumber.
Placement of jibs in corners. Leads to a decrease in the rigidity and stability of the structure.

Consequences of building a frame house without jib
Refusal to use jib beams in the construction of a frame house can lead to disastrous consequences:
destruction of the house under the influence of snow and wind loads;
external cladding plywood (it has a high degree of spatial rigidity compared to chipboard, OSB, etc.) does not provide the necessary rigidity;
under the influence of soil movement, the house can “walk” on its own;

Temporary jib
Installation of temporary jibs is a necessary step during the construction of the building frame. They are used:
During installation of corner posts. Temporary jibs prevent the connection between the corner post and the bottom frame from becoming loose until installation top harness.
For leveling frame walls and eliminating following problems when installing doors, windows, interior and exterior finishing. When the doors are not hung, but finishing slabs do not meet in the corner.
For installation and alignment of rafters under the roof.

The procedure for installing temporary jibs:
1. First we align the corners. For this operation, you can use a bubble or laser level. You can also use the “American” method. Secure the level to a board as long as the height of the wall.
2. Temporary jibs are fastened with blocks secured to the floor or platform at the bottom and to the upper joists at the top.
3. The installation pitch of the jib is from 1.2 m to 1.5 m. They are made from boards with a section of 25x150 mm.
With the help of temporary jib, you can correct significant defects by creating the necessary leverage.

Do-it-yourself jibs

Although jibs are an important element of a frame house, making them yourself will not be particularly difficult:
1. As a rule, a board with a cross-section of 25x100 mm is used (for areas with increased wind load, a cross-section of 50x100 mm is recommended). The length of the board should be 30% longer than the height of the wall.
2. Apply it to the vertical posts at an angle of 45 - 60 ° (depending on the design of the wall, where it turns out). We mark the grooves in the racks, from the upper to the lower joists. The jib should come from the center of the wall, the top should be directed towards the upper corner of the post, and the bottom should be moved as far as possible.
3. With a regular hacksaw or manual circular saw We make grooves and remove the wood with a chisel. The corners of the jib itself are also trimmed along the outsole.
4. The jib must fit tightly into the grooves made to ensure maximum rigidity.
5. In window and doorways It is recommended to place the jibs from the corner to the hole. Thus, additional fastening of the opening pillars is carried out.
6. The jibs are fastened with 2 nails. for each vertical stand and 3 pcs. on the top and bottom trim.
By following these steps in the manufacture of jibs, you will obtain the necessary rigidity of your structure to withstand wind and snow loads.

Have you ever encountered the topic of “correct” or “wrong” frame house popping up in discussions on forums? Often people are pointed out that the frame is wrong, but they find it difficult to really explain why it is wrong and how it should be. In this article I will try to explain what is usually hidden behind the concept of a “correct” frame, which is the basis of a frame house, just like a human skeleton. In the future, I hope we will consider other aspects.

Surely you know that the foundation is the foundation of the house. This is true, but a frame house has another foundation - no less important than the foundation. This is the frame itself.

Which frame house is “right”?

I'll start with the basics. Why is it so difficult to talk about the right frame house? Because there is no single correct frame house. What a surprise, isn't it? 🙂

You will ask why? Yes, very simple. A frame house is a large constructor with many solutions. And there are many decisions that can be called correct. There are even more decisions – “half-correct” ones, but the “wrong” ones are legion.

Nevertheless, among the variety of solutions, one can single out those that are usually meant when speaking about “correctness.” This is an American and, less commonly, Scandinavian type frame.

Why are they considered examples of “correctness”? Everything is very simple. The vast majority of private homes for permanent residence in America, and a very significant percentage in Scandinavia, are built using frame technology. This technology has been used there for decades and perhaps even a hundred years. During this time, all possible bumps were filled, all possible options were sorted out and some universal scheme was found that says: do this and with a 99.9% probability everything will be fine. Moreover, this scheme is the optimal solution for several characteristics:

Constructive reliability of solutions.
Optimal labor costs during construction.
Optimal cost of materials.
Good thermal characteristics.

Why step on your own rake if you can take advantage of the experience of people who have already stepped on this rake? Why reinvent the wheel if it has already been invented?

Remember. Whenever we talk about the “correct” frame or the “correct” components of a frame house, then, as a rule, this means standard solutions and components used in America and Scandinavia. And the frame itself satisfies all the above criteria.

What frames can be called “semi-regular”? Basically, these are those that differ from typical Scandinavian-American solutions, but, nevertheless, also satisfy at least two criteria - reliable design and good solutions in terms of heating engineering.

Well, I would classify all the rest as “wrong”. Moreover, their “wrongness” is often conditional. It is not at all a fact that the “wrong” frame will necessarily fall apart. This scenario is actually extremely rare, although it does occur. Basically, the “wrongness” lies in some controversial and not the best decisions. As a result, things get complicated where things can be done easier. More material is used where less is possible. The design is made colder or more inconvenient for subsequent work than it could be.

The main disadvantage of “wrong” frames is that they provide absolutely no gains compared to “correct” or “semi-correct” ones - neither in reliability, nor in cost, nor in labor costs... nothing at all.

Or these advantages are far-fetched and generally doubtful. In extreme cases (and there are some), improper framing can be dangerous and will result in a major home renovation being required within just a few years.

Now let's look at the question in more detail.

Key features of the American frame

The American frame is practically a standard. It is simple, strong, functional and reliable as an iron saw. It is easy to assemble and has a large margin of safety.

Americans are tight-fisted guys, and if they manage to save a couple of thousand dollars on construction, they will definitely do it. At the same time, they will not be able to stoop to outright hackwork, since there is strict control in the construction field, insurance companies in case of problems will refuse to pay, and customers of unfortunate builders will quickly sue and rip off negligent contractors like a stick.

Therefore, the American frame can be called the standard in terms of the ratio: price, reliability, result.

The American frame is simple and reliable

Let's take a closer look at the main points that distinguish the American frame scheme:

Typical components of a frame house

Timber in racks and frames is almost never used, unless this is due to some specific conditions. Therefore, the first thing that distinguishes a “correct” frame house is the use of dry lumber and the absence of timber in the walls.

Points that distinguish the American frame:

Corners - there are several different schemes for implementing corners, but nowhere will you see timber as corner posts.
Double or triple racks in the area of window and door openings.
The reinforcement above the openings is a board installed on the edge. The so-called “header” (from English header).
Double top frame made of boards, no timber.
The overlap of the lower and upper rows of trim at key points - corners, various fragments of walls, places where internal partitions join external walls.

I didn’t specifically mention Ukosina as a distinctive point. Since in the American style, if there is cladding with OSB3 (OSB) boards on the frame, there is no need for miters. The slab can be considered as an infinite number of jibs.

Let's talk in more detail about the key features of the correct frame in the American version.

Correct corners of a frame house

In fact, on the Internet, even in the American segment, you can find a dozen schemes. But most of them are outdated and rarely used, especially in cold regions. I will highlight three main angle patterns. Although realistically, only the first two are the main ones.

Nodes of corners of a frame house

Option 1 – the so-called “California” angle. The most common option. Why exactly “California” – I have no idea :). From the inside, another board or strip of OSB is nailed to the outer post of one of the walls. As a result, a shelf is formed on the inside of the corner, which subsequently serves as a support for the interior decoration or any internal layers of the wall.
Option 2 – closed corner. Also one of the most popular. The essence is an additional stand in order to make a shelf on the inner corner. Among the advantages: the quality of insulation of the corner is better than in option 1. Among the disadvantages: such a corner can only be insulated from the outside, that is, this must be done before sheathing the frame with anything from the outside (slabs, membrane, etc.)
Option 3 – “Scandinavian” warm corner. A very rare option, not used in America. I have seen it in Scandinavian frames, but not often. Why did I bring him then? Because, in my opinion, this is the warmest corner option. And I'm thinking about starting to use it at our facilities. But you need to think before using it, since it is structurally inferior to the first two and will not fit everywhere.

What is unique about all three of these options and why is timber a bad option for a corner?

Angle made of timber, the worst option

If you noticed, in all three options made of boards, the corner can be insulated. Somewhere more, somewhere less. In the case of timber in a corner, we have two drawbacks: firstly, from the point of view of heating engineering, such a corner will be the coldest. Secondly, if there is a beam in the corner, then there are no “shelves” on the inside to attach the interior trim to it.

Of course, the last issue can be resolved. But remember what I said about the “wrong” frames? Why make it complicated when you can make it simpler? Why make a beam, creating a cold bridge and thinking about how to attach finishing to it later, if you can make a warm corner from boards? Despite the fact that this will not affect the quantity of material or the complexity of the work.

Openings and top trim are the most significant difference between the American frame design and the Scandinavian one, but more on that later. So, when they talk about the correct openings in a frame, they usually talk about the following scheme (window and door openings are made according to the same principle).

Correct openings in frame house

The first thing (1) that people usually pay attention to when talking about “wrong” openings is the double and even triple racks on the sides of the opening. It is often believed that this is necessary to somehow strengthen the opening for installing a window or door. Actually this is not true. A window or door will be fine on single posts. Why then do we need cohesive boards?

Everything is elementary. Remember when I said that the American frame is as simple and reliable as an iron saw? Pay attention to Figure 2. And you will understand that solid racks are needed solely to support the elements lying on them. So that the edges of these elements do not hang on nails. Simple, reliable and versatile.

In Figure 3 there is one of the simplified versions, when the lower frame of the window cuts into a torn mullion. But at the same time, both window frames still have supports at the edges.

Therefore, we cannot formally say that if the racks are not doubled, then this is “wrong.” They can also be single, as in the Scandinavian frame. Rather, the mistake is when the racks along the edges of the openings are solid, but do not bear the load from the elements resting on them. In this case they are simply meaningless.

In this case, the horizontal elements hang on fasteners, so there is no point in doubling or tripling the racks on the sides

Now let's talk about an element that is already more critical and the absence of which can be considered as an “irregularity” of the opening. This is the “header” above the opening (header).

Window header

This is a really important element. As a rule, some kind of load will come from above onto the window or doorway - the floor joists of the second floor, the rafter system. And the wall itself is weakened by deflection in the area of the opening. Therefore, local reinforcements are made in the openings. In American it is headers. In fact, this is a board installed on edge above the opening. Here it is important that the edges of the header either rest on the posts (if the classic American scheme with solid opening posts is used), or are cut into the outer posts if they are single. Moreover, the cross-section of the header directly depends on the loads and dimensions of the opening. The larger the opening and the stronger the load on it, the more powerful the header. It can also be double, triple, extended in height, etc. – I repeat, it depends on the load. But, as a rule, for openings up to 1.5 m in width, a header made from a 45x195 board is quite sufficient.

Is the absence of a header a sign that the framework is “wrong”? Yes and no. If we act according to the American principle of “simple and reliable,” then the header should be present at every opening. Do this and be sure of the result.

But in fact, you need to dance from the load falling on the opening from above. For example, a narrow window in a one-story house and the rafters in this section of the wall are located along the edges of the opening - the load from above on the opening is minimal and you can do without a header.

Therefore, the header issue should be treated as follows. If there is one, great. If it is not there, then the builders (contractor) must clearly explain why, in their opinion, it is not needed here, and this will depend, first of all, on the load falling on the opening area from above.

Double top harness

Double top frame made of boards, also a distinctive feature of the American frame

Double top harness

The double strapping again provides reinforcement along the top of the wall for deflection from the load from above - the load from the ceiling, rafters, etc. In addition, pay attention to the overlaps of the second row of strapping.

Overlap in the corner - we tie two perpendicular walls together.
Overlap in the center - we tie together 2 sections of one wall.
Overlap along the partition - we tie the partition together with the outer wall.

Thus, the double piping also fulfills the second task - ensuring the integrity of the entire wall structure.

In the domestic version you can often find the top frame made of timber. And this, again, is not the best solution. Firstly, the beam is thicker than a double frame. Yes, it may be better for deflection, but it is not a fact that it is necessary, but the cold bridge at the top of the wall will be more significant. Well, it’s more difficult to implement this overlap to ensure the integrity of the entire structure. Therefore, we return again to the question: why make it difficult if you can make it simpler and more reliable?

Correct jib in a frame house

Another cornerstone. Surely you have come across the phrase “jibs made incorrectly.” Let's talk about this. Firstly, what is a jib? This is a diagonal element in the wall, which provides spatial rigidity for shear in the lateral plane. Because thanks to the jib, a system of triangular structures appears, and the triangle is the most stable geometric figure.

So, when they talk about the correct jib, they usually talk about this option:

Correct jib

Why is this particular jib called “correct” and what should you pay attention to?

This jib is installed with an angle of 45 to 60 degrees - this is the most stable triangle. Of course, the angle may be different, but this range is best.
The jib cuts into the upper and lower trim, and does not just rest against the rack - this is quite an important point, in this way we tie the structure together.
The jib cuts into every post in its path.
For each node - adjacent to the harness or rack, there must be at least two fastening points. Since one point will give a “hinge” with a certain degree of freedom.
The jib cuts into the edge - this way it works better in the structure and interferes less with the insulation.

And here is an example of the most “wrong” jib. But nevertheless, it occurs all the time.

This is just a board stuck into the first opening of the frame. What is so “wrong” about it, since formally it is also a triangle?

Firstly, the angle of inclination is very small.
Secondly, the jib board works worst in this plane.
Thirdly, it is difficult to fix such a jib to the wall.
Fourthly, pay attention to the fact that cavities that are extremely inconvenient for insulation are formed at the junctions with the frame. Even if the jib is carefully trimmed and there is no gap at the end, there is no escape from the sharp corner, and properly insulating such a corner is not an easy task, so most likely it will be done somehow.

Another example, also common. This is a jib cut into the posts, but not cut into the harness.

The jib is not embedded in the harness

This option is already much better than the previous one, but, nevertheless, such a jib will work worse than one embedded in the harness, and the work will take 5 minutes more. And if, moreover, it is fixed to each rack with only one nail, then its effect will also be minimized.

We won’t even consider the options for all sorts of small defective “corners and braces” that do not reach from the top harness to the bottom.

Formally, even the most crooked jib makes at least some contribution. But once again: why do it your own way if a good solution already exists?

This is where we finish with the American frame and move on to the Scandinavian one.

Correct Scandinavian frame

Unlike America, where frames are practically standardized and there are very few differences, there are more variations in Scandinavia. Here you can find both the classic American frame and hybrid versions. The Scandinavian frame, in essence, is the development and modernization of the American one. However, basically, when they talk about a Scandinavian frame, we are talking about such a design.

Typical Scandinavian house kit

Scandinavian frame

Corners, jibs - everything here is like the Americans. What should you pay attention to?

Single strapping along the top of the wall.
Power crossbar embedded in the racks along the entire wall.
Single posts on window and door openings.

In fact, the main difference is this very “Scandinavian” crossbar - it replaces both the American headers and the double harness, being a powerful power element.

What, in my opinion, is the advantage of the Scandinavian frame over the American one? The fact is that it places a much greater emphasis on minimizing all kinds of cold bridges, which are almost all solid boards (double strapping, racks of openings). After all, between each solid board, a gap could potentially form over time, which you may never know about. Well, it’s one thing when the cold bridge is the width of one board, and another question is when there are already two or three of them.

Of course, you shouldn’t focus on cold bridges. There’s still no escape from them, and in fact, their importance is often exaggerated. But, nevertheless, they exist and, if it is possible to minimize them relatively painlessly, why not do it?

Scandinavians in general, unlike Americans, are very concerned about energy saving. The colder, northern climate and expensive energy resources also have an impact. But in terms of climate, Scandinavia is much closer to us (I’m talking primarily about the North-West region) than most American states.

The disadvantage of the Scandinavian frame is that it is slightly more complex, at least in the fact that in all racks you need to make cuts for the crossbar. And the fact is that, unlike the American one, it does require some kind of mental effort. For example: large openings may require double racks to support horizontal elements, and additional crossbars and headers. And somewhere, for example, on the gable walls of one-story buildings, where there is no load from the joists or roof, perhaps a transom is not even needed.

In general, the Scandinavian frame has certain advantages, but requires a little more effort and intelligence than the American one. If the American frame can be assembled with the brains completely turned off, then in the Scandinavian one it is better to turn them on, at least in the minimum mode.

“Semi-regular” frames

Let me remind you that by “semi-correct” I mean precisely those that have every right to exist, but differ from the typical Scandinavian-American solutions. Therefore, calling them “semi-correct” must be done with caution.

Let me give you a few examples.

An example of how you can “overdo it”

The first example is from our own practice. This house was built by us, but according to a design provided by the customer. We even wanted to redo the project completely, but we were limited by deadlines, since we had to go to the site; In addition, the customer paid a significant amount for the project and formally there are no violations in the design, but he has come to terms with the stated shortcomings of the current solution.

Why then did I classify this frame as “semi-regular”? Please note that there are Scandinavian crossbars, American headers, and double trims not only at the top, but also at the bottom of the walls. In short, there is an American scheme, and a Scandinavian one, and another 30% of the Russian reserve is thrown on top, just in case. Well, the prefabricated stand of 6 (!!!) boards under the glued ridge beam speaks for itself. After all, in this place the only insulation is isoplate on the outside and cross-insulation on the inside. And if there was a purely American scheme, then there would simply be no insulation in this section of the wall, bare wood from the outside in.

I call this frame “semi-correct” because from the point of view of structural reliability there are no complaints about it. There is a multiple margin of safety “in case of nuclear war.” But there are an abundance of cold bridges, a huge waste of material for the frame, and high labor costs, which also affects the price.

This house could have been made with a smaller but sufficient margin of safety, but at the same time reducing the amount of lumber by 30 percent and significantly reducing the number of cold bridges, making the house warmer.

Another example is a frame using the “double volume” frame system, promoted by a Moscow company.

The main difference is that it is actually a double outer wall, with racks spaced apart relative to each other. So the frame fully satisfies the strength criteria and is very good from the point of view of thermal engineering, due to the minimization of cold bridges, but loses in manufacturability. The problem of eliminating cold bridges, which is primarily solved by such a frame, can be solved by simpler, more reliable and correct methods such as “cross-insulation”.

And, curiously, usually “semi-correct” frames somehow contain Scandinavian-American solutions. And the differences are rather in an attempt to improve the good. But it often happens that “the best is the enemy of the good.”

Such frames can be safely called “semi-correct” precisely because there are no gross violations here. There are differences from typical American-Scandinavian solutions in attempts to improve something or come up with some kind of “trick”. Whether to pay for them or not is the customer’s choice.

“Wrong” frame houses

Now let's talk about the “wrong” frames. The most typical, I would even say collective, case is presented in the photo below.

The quintessence of “directional” frame house construction

What can you immediately notice in this photo?

Total use of natural moisture material. Moreover, it is a massive material, which dries out the most and changes its geometry during the drying process.
The beams in the corners and on the straps and even on the racks are cold bridges and an inconvenience in further work.
Lack of headers and opening reinforcements.
Do not understand how the jib is made, poorly fulfilling its role and interfering with insulation.
Assembly on corners with black self-tapping screws, the purpose of which is to fasten gypsum boards during finishing (and not for use in load-bearing structures).

The photo above shows almost the quintessence of what is commonly called an “irregular” frame or “RSK”. The abbreviation RSK appeared in 2008 at FH, at the suggestion of one builder who presented a similar product to the world, called Russian Power Frame. Over time, as people began to figure out what was what, this abbreviation began to be deciphered as Russian Strashen Karkashen. Like the apotheosis of meaninglessness with a claim to a unique solution.

What is most curious is that, if desired, it can also be classified as “semi-correct”: after all, if the screws do not rot (black phosphated screws are by no means an example of corrosion resistance) and do not burst during the inevitable shrinkage of the timber, this frame is unlikely to fall apart. That is, such a design has the right to life.

What is the main disadvantage of “wrong” frames? If people know what they are doing, they will come to the Canadian-Scandinavian pattern pretty quickly. Fortunately, there is a wealth of information now. And if they don’t come, then this says one thing: they, by and large, don’t care about the result. The classic answer when trying to ask them why this is so is “we have always built it this way, no one has complained.” That is, the entire construction is based solely on intuition and ingenuity. Without trying to ask how it’s generally customary to do this.

What prevented you from making a board instead of timber? Reinforce the openings? Make normal jibs? Collect on nails? That is, do it right? After all, such a frame does not provide any advantages! One large set of not the best solutions with claims to super strength, etc. Moreover, the labor input is the same as the “correct” one, the cost is the same, and the material consumption is perhaps even greater.

Summarize

As a result: the American-Scandinavian frame scheme is usually called “correct”, due to the fact that it has already been tested many times on thousands of houses, proving its viability and the optimal ratio of “labor-input-reliability-quality”.

“Semi-regular” and “irregular” include all other types of frames. In this case, the frame may be quite reliable, but “suboptimal” in terms of the above.

As a rule, if potential contractors cannot justify the use of certain design solutions other than the “correct” American-Scandinavian ones, this indicates that they have no idea about these very “correct” solutions and are building a house solely on a whim, replacing knowledge with intuition and ingenuity. And this is a very risky path that may come back to haunt the home owner in the future.

That's why. Do you want guaranteed correct, optimal solutions? Pay attention to the classic American or Scandinavian frame house construction scheme.

about the author

Hello. My name is Alexey, you may have met me as Porcupine or Gribnick on the Internet. I am the founder of the Finnish House, a project that has grown from a personal blog into a construction company whose goal is to build a high-quality and comfortable home for you and your children.

From the above, it is not difficult to understand that the presence of a jib in a wooden house is not a whim, but a necessity. Below are the basic recommendations for its correct installation:

To achieve maximum rigidity of the building, it should be placed at an angle of 45 degrees, but, unfortunately, it is difficult to adhere to the exact value in places where window or door openings are located. For this reason, it is entirely possible to install the jib at an angle of no more than 60 degrees; in this case, an increase in the angle value can be successfully compensated by increasing the number of jib.
The use of a hollow jib when creating frames is highly discouraged. Hollow ones are excellent for small-sized (most often one-story) buildings, and only if there are flexible connections.
The jib should fit snugly to the edges of the racks and ceilings, without forming gaps.
Special grooves must be made not only in the vertical posts, but also in the upper and lower trim. The depth and size of the groove directly depends on the thickness of the jib.
It has different cross-sectional dimensions, which are always calculated individually for each region. Sizing calculations depend on requirements based on state building codes. There are no universal meanings.
The corner ribs are attached to the vertical posts using two or three nails.

During the installation of the jib, the following factors are unacceptable:

You should not use wood from forests with artificial moisture, since the boards instantly “shrink out”, forming significant gaps in places of tight joints, reducing the reliability of the structure.
The use of low-quality lumber in construction is prohibited.
It is not recommended to install in corners as this may compromise the overall stability and durability of the house.

Versatility, durability, safety and reasonable prices make the construction of frame houses the most profitable and practical solution. Our company specializes in construction

The durability of a building primarily depends on its stability. Any structure, and even more so one as complex and voluminous as a house, is subject to a number of external influences and internal stresses. Seismic vibrations, soil shifts, wind - all this tends to destroy any house. Uneven shrinkage, pockets of dampness, structural loads - this undermines the building from the inside. In a frame house, the elements that ensure its maximum stability are the jibs.

1. Structural loads on the house

In most cases, any building has the shape of a parallelepiped. Any quadrangle is not the most durable structure. The slightest deviation of any of its sides causes deviation of the other sides, since they are connected to each other.

The ideal one from this point of view is a triangle with maximum rigidity. Thus, the strongest molecules are carbon molecules that form a pyramid.

It is the addition of additional elements to the structure that introduce “triangularity” into them that forms the basis of all rigid fastenings of the quadrangle.

So, a tablet with slats or plywood triangles stuffed in the corners will be much stronger compared to the original one.

Frame reinforced at corners

This is what is often used in construction, especially in the construction of frame houses. After all, a frame house is an ideal parallelepiped, and all the blocks from which it is composed are rectangular in shape.

Moreover, any lateral load, for example, a strong wind, tends to disrupt the right angles at the base of these quadrangles. The result can be disastrous - the house can tilt severely or even fall on its side.

House “fastened” with clapboard

2. What are jibs?

The building frame is a set of racks reinforced between the lower and upper frames with some spacing between them. The racks are made from boards and placed perpendicular to the perimeter line

This design provides resistance only under vertical loads. Under horizontal loads, the row of racks tends to tilt. If the pillars are not further strengthened, the house may collapse.

It is the board, placed on top of the posts at an angle to them, that holds them strictly in a vertical position. It's called a jib.

3. Is it possible to do without jibs?

There is an opinion that jibs for a frame house are not so important. It would seem that if you cover the frame with sheet material (plywood or OSB), the walls will acquire additional resistance to lateral loads.

Moreover, careless builders allow the external finishing of the frame directly on top of the racks - in the hope that it will give the house sufficient rigidity.

But this is not entirely true. Sheets of fibreboard, plywood or OSB, of course, additionally fasten the building themselves, but their size only affects the connection inside the frame cell, and not the entire frame. After all, the very design of the hinge joint, which is a frame house, assumes the absence of the necessary stiffeners to prevent lateral loads.

What can we say about the elements of external decoration, such as siding, facing slab, lining, which are not attached to the wall so rigidly and may themselves be fragile.

Conclusion: it is necessary to install jib bars.

Sometimes jib bars are confused with struts. They really give rigidity to individual elements, for example the quadrangular cell of a block, but do not affect the entire frame as a whole.

4. Installation of jibs

We'll tell you how to install the jib correctly.

As we said above, the jib is a board that is attached on top of the racks at a certain angle to the floor. As a rule, it is enough to use boards with a section of 25x100 mm. They are ideally installed at an angle of 45 degrees relative to the floor plane. They are installed from the center of the wall to the corners of the ceiling. The length of the jib boards, accordingly, can exceed the length of the racks by 30%

Due to the fact that not all walls remain solid, it is sometimes impossible to install long jibs at an angle of 45 degrees. On walls where there are window and door openings, it is necessary to install the jibs at a different angle, usually no more than 60 degrees.

Let us note an important fact. Jib beams need to be done not only on external, but also on load-bearing internal walls. This will give the house maximum rigidity.

In general, you need to remember the main rules for installing jib

The slope of the jibs tends to 45 degrees.
The lower part is placed closer to the center of the wall, the upper part - to the upper corner.
The jib should be maximally connected to the frame and frame posts.

5. Features of jib installation

The installation of the jibs is carried out flush with the plane of the racks. To do this, grooves are cut out in the frame racks into which they are inserted. Corresponding grooves are cut in both the upper and lower trim. Only then will the jibs be as effective as possible. The jibs are attached to the ceiling and floor trim using powerful bolts or powerful self-tapping screws. They are nailed to the posts with at least two nails, reducing the hinge of the structure.

In the process of forming the wall, the blocks are lifted one by one, and they need to be given stability - up to the complete assembly of the frame with the upper frame. To do this, use temporary jibs. It makes no sense to spare material on them, as later these boards can easily be torn off and used.

It is permissible to install temporary jibs without cutting into the posts and strapping.

7. Mistakes when installing jibs

Let's note some mistakes that builders make:

The installation angle is too high relative to the floor
Absence of jibs at all or on internal walls
Non-rigid attachment to the frame and frame posts
Poor quality material, use of defective boards
Insufficient length of the jib, use of scraps stuffed chaotically

8. Conclusions

Thus, for maximum stability of the frame, the jibs are considered a necessary element of the entire structure. They must be installed from high-quality materials and strictly in accordance with the above recommendations.