Decorative fence. Decorative fence for a summer residence: plastic, metal. Options for building materials in the photo

Your own yard or summer cottage requires constant care. Many land owners strive to make their yard cozy and well-groomed. You can do a lot with your own hands at the dacha, if you have the desire. One of the decorative items is a fence, which will not only decorate the yard, but will also allow you to divide the territory into recreation areas, planting areas, flower beds, fountains, etc.

Decorative fence for a summer residence

Every summer resident can find a lot of materials from which you can build a decorative fence with your own hands. To do this, you don’t need to have any special skills or knowledge, you just need to use your imagination and get down to business. It is worth noting that a decorative fence can become a full-fledged fence if it is erected along the entire perimeter of the site.

Decorative fence made from scrap materials

Available materials for building a fence include:

Old bricks;
unnecessary rubber cylinders;
croaker;
willow twigs, etc.

A tall decorative fence is easiest to build from brick. The method of laying this building material known to everyone.

Decorative fence made of twigs

Decorative wicker fence

To build such a fence you will need oak stakes and willow branches.

Before weaving, the branches must be soaked in water for 24 hours.
While the rods are soaking, you need to drive oak stakes into the ground.
The height of the posts should correspond to the desired height of the finished fence (60-100 cm). The stakes are driven into the ground to a depth of 20-30 cm at a distance of 1 m from each other.
After the stakes are driven in and the rods are soaked, you can begin to weave the fence. The rods are threaded between the stakes so that one stake is in front and the second is at the edge of the rod.
Thus, alternating the front and back rods, we weave a fence. If you want to make the tyn dense, without cracks, tamp down each layer with a wooden mallet.

You can create a vertical weave in the same way. In this case, you need to nail 3-4 more guides between the stakes. How to make weaving is up to you; in any case, this type of fence will look unusual and will attract the attention of neighbors to your site.

Instead of a tyn, you can build a fence from a slab. It looks quite colorful and gives the site the appearance of a village yard.

For such a fence you will need 5*10 cm square beams, a slab, nails and a hammer.

We drive the beams into the ground 20-30 cm, at a distance of 1-1.5 m from each other.
We nail boards to the supports, with the uncut side facing the street.
After installation, the boards can be coated with several layers of varnish so that the fence lasts for many years and does not lose its attractiveness.

Among the finished products, we can highlight concrete decorative fences, which will be an excellent protection for your home from uninvited guests. These fences come in a variety of textures, shapes and designs. They can be painted in any color and decorated in any style.

The only disadvantages of such fences are the relatively high cost and labor-intensive installation.

Unlike a full-fledged fence, a decorative fence is not high.

Its maximum height is 40 cm.

Such fences are used to frame paths, highlight planting zones, protect the garden from domestic animals, decorate flower beds, etc.

Before you start construction, you need to choose what to make the fence from. You can build a decorative fence with your own hands, from scrap materials, it can be:

Brick;
plastic bottles;
logs;
stones;
remains of slate, etc.

From stone

One of the most interesting options is a fence made of natural stone.

This fence will fit perfectly into the natural landscape. summer cottage and will help create a unique territory design. Natural stone is used not only to designate flower beds and alleys; it can also be used to lay out the paths themselves, combining all parts of the site into a single design line.

There are many design options for such a fence.

It all depends on your imagination. You can insert not only the stones themselves into the fence, but also driftwood, clay vases and other decorative elements. In order for the fence to be strong, the masonry must be secured with cement.

From bottles

Glass bottles also look unusual.

To create such a fence, you need to dig a small trench around the perimeter of the fence and install bottles in it at the required height. To make the structure strong and durable, the bottles should be filled with sand or crushed stone. How to make a bottle ornament depends on your landscape. A fence can go around flower beds, trees, or simply act as a straight path limiter.

From logs

If you have a bathhouse at your dacha, you will probably find the remains of sawn logs. Select logs of the same length, 20-30 cm, with a diameter of 40-50 mm, and drive them into the ground around the flower bed tightly to each other. Such a fence will give unusual look your site and will last for more than one year.

From slate

To make a fence from the remains of slate, it is enough to dig pieces of this building material into the ground. A slate fence will not last long, but it will help separate the flowerbed or bed from the rest of the site for a couple of seasons.

Made of brick

A brick structure will be more durable. A small fence can be built by simply digging bricks vertically into the ground, as close together as possible. If you want to create a more voluminous structure, you will have to use your imagination. Brick can be used to cover multi-tiered flower beds, small ponds and paths. When laying this material, cement is traditionally used for adhesion.

Today on the market you can find many options for decorative plastic fences. They can be purchased sectionally and easily assembled on your site. Fencing made of plastic elements has a number of advantages, namely:

Easy installation from ready-made elements.
A variety of shapes, colors and textures.
Low weight.
Inexpensive cost.
Resistance of the structure to rotting and deformation.

Plastic decorative fencing can be used to design zones of any geometry. They come in different heights and designs. Thanks to the use special type Limination, plastic elements can emit wood, natural stone, forging or wattle.

Installation of a decorative plastic fence

To install a fence on your property:

You need to measure the perimeter of the fenced area and purchase a ready-made fence of the required length.
Plastic decorative posts are sold complete with fencing sections.
Installation of the structure is not difficult. It is necessary to assemble the structure and, using a wooden hammer, drive the pillars into the ground to the indicated mark.

Care

However, in order for such a fence to please you for many years, you need to know some of the nuances of caring for plastic. Firstly, plastic does not tolerate low temperatures. After exposure to cold, the material deteriorates, cracks and chips. To avoid damage to the fence in the winter months, at the end of the summer season it is better to dismantle it and put it in the pantry until spring. Secondly, plastic does not like rough cleaning. When washing the fence, do not use abrasive powders, iron brushes and chloride compounds. Thirdly, such fences cannot be painted. Choose the color you want immediately upon purchase. When repainting plastic, you run the risk of paint peeling or uneven coloring.

Species

Most often on the market you can find plastic fences with a height of 13 to 20 cm. These designs are perfect for highlighting paths and flower beds. To zone a yard or fence a garden, you should look for fences with a height of 40 cm.

Metal fences remain the most popular for decoration summer cottages and areas of country houses. Forged products come in a variety of shapes, sizes and design options. A metal fence can act as either a limiter for garden paths or a full-fledged fence for the area.

Decorative metal fences can be purchased in specialized stores or ordered according to an individual sketch. These products are strong and durable.

Installation

You can make a decorative wrought iron fence yourself. To do this you will need metal corners for the frame, fittings and forged elements decorations.

However, it will not be possible to assemble such a fence without special equipment and certain skills. In order to make a decorative wrought iron fence, you need to have a welding machine.

If you have neither the skills nor a welding machine, and buying a turnkey fence is expensive for you, you can purchase separate sections that are installed independently. The installation method directly depends on the chosen design. Sections can be attached to metal pipes or between concrete decorative pillars.

Care

Iron decorative fences do not need to be dismantled for the winter, but they do require annual painting. The coating will protect the metal from corrosion and extend the life of the fence. With proper care, such fences can easily last 20 years or more.

Forged products look best against the background of stone or brick paths, alpine slides And decorative fountains. Iron decorative fences are most often installed permanently. To do this, the fence posts are concreted so that the fence does not deform in the future. In this case, the main frame should be at a height of 2 cm above the ground. To install a high metal fence, it is necessary to build a foundation.

You can fence your own garden or vegetable garden using various fencing options. Here the choice depends on the purpose of the fence. If there are pets in the house, it is better to make a decorative fence for the vegetable garden higher, but if it is just zoning the site, you can build a low decorative fence.

It can be an excellent option for fencing a garden. This type of fencing will have to be planted and cultivated with your own hands, but the result will certainly compensate for all these efforts.

Best suited for hedges:

Seedlings of which can be bought at flower markets and specialized bazaars.
After you have planted the bushes around the perimeter, they should take root.
It is better to give the plants a year to do this.
In the second year, the bushes can already be trimmed, giving them unusual and bizarre shapes.

You can also make a decorative fence for a fence yourself from stakes in the shape of pencils.

Such fences can often be found on the territory of children's development centers and gardens. To create such a fence you will need pointed logs of different lengths, 7-10 cm in diameter and paint different colors.

Drive the pencils into the ground, perhaps at intervals, and paint them in different colors. Such a garden fence will delight with its colorfulness and will give a good mood to the owners and guests of the house.

Decorative fence You can also make a garden fence from a picket fence.

To do this, you will need strips - guides and pickets.

Lay the slats on the ground and nail pickets to both slats so that they are the same distance apart.
The finished structure can be nailed to pegs pre-installed in the ground.

Other options

When wondering how to decorate your site with decorative fencing, you just need to show a little ingenuity and imagination. Often every summer resident has materials for non-standard and interesting fencing. If you think about it a little, you can build a decorative fence from the most common means at hand. For example, a birch fence is made from birch branches. It can be attached using the classic method, to stakes horizontally. And create fancy patterns from branches.

A decorative wicker fence made from ordinary branches can be decorated with clay jugs, or you can weave it according to your own design. As a result, you can create unique compositions that will decorate the yard and will not require special costs. Decorative wicker fences can be made in any shape and size.

A decorative fence made of branches can be made in the form of snags fastened together. This type of fence is perfect for fencing your garden and vegetable garden from domestic animals. The branches for such a fence should be chosen bent and fancy. They are attached to the main pillars located at a distance of 1-1.5 m.

A decorative fence made of rods can be created very simply by having 2 pieces of steel wire on hand. The wire is stretched over the stakes, and rods are inserted vertically between it. A decorative slab fence or a decorative log fence also looks great on the site.

Every owner local area tries to ennoble it as much as possible or according to his aesthetic idea. Fences and borders play an important role in decorating a site. They will help to implement zoning, for example, to separate part of the space for recreation with a barbecue, benches, gazebos. With their help, you can select beds for vegetables or berries, as well as decorate flower beds in a beautiful and original way, and preserve the geometry of flower beds. In the article we will consider various types decorative fence and methods of their manufacture.

Such fences will not only give a neat appearance to the site, but will also cope with their intended purpose - they will protect the plantings from careless guests and serve as a barrier for domestic animals. And here it doesn’t matter at all whether it’s a dacha where only a few seasons are held, or private house for year-round use.

It should be noted right away that all of the fencing options listed below can frame absolutely any shape of paths, flower beds and create dividing zones. There is no limit to imagination in these works; they are mounted in the form of strict geometric shapes or non-standard lines.

Plastic decorative fences

There are a huge variety of fences of this kind on the market, thanks to the technical characteristics of the material from which they are made. Its thermoplasticity makes it possible to create borders for paths and fencing flower plantings, front gardens of various shapes, and a special lamination method - in various colors.

Here you can give preference to a tape border or sectional type, which will serve as a marking of the boundaries of garden paths, and will also become an additional decoration for plant compositions.
Each section is equipped with pegs, so the installation process consists of light pressure until the supports are completely embedded in the ground. Installation can be carried out both on absolutely flat surfaces and on ground with a slight slope.
Decorative fences for a summer residence made of plastic can imitate a wooden picket fence, wattle fence, clinker or stone masonry, and forged elements. Typically, such sections are made in height from 13 to 20 cm.

Decorative wooden fences

The most popular material for making a yard look well-groomed is still wood. Such fences look quite relaxed in the landscape and do not create any disharmony.

Another advantage of the material is its availability, because for finishing, for example, flower beds, any lumber is suitable: boards, slats, pegs, logs and even branches. Here we mean the production of standard fences, only in miniature sizes.

Before carrying out any work, wood requires mandatory processing:

the lower part of the supports, entering the ground, must be burned or dipped into liquid roofing felt;
all other structural elements are impregnated with special solutions that slow down the rotting process and protect against insects.

"Plank fence"

To make a structure 40 cm high to frame a flower bed 70x70 cm you will need:

4 beams 50x50x700 mm;
8 boards 20x100x700 mm (here, if desired, you can use both edged and unprocessed lumber);
32 wood screws or the same number of nails;
screwdriver, hammer.

Stages of work

Drive the supports into the ground 700 mm apart, check the vertical and adjust their height.
A board is attached to the top of the beam in two places, where its end part should not protrude beyond the edge of the peg.
The second cross member is mounted at a distance of 100 mm from the bottom edge of the board.
The same manipulations are performed on other sides of the flower bed.

"Lattice"

With this lightweight slatted fence you can fence off a flowerbed with tall plants, for example, such as: sapling or basil. If you perform it more large sizes, then it is perfect for separating a recreation area.

To implement it, one section with dimensions 900x630 mm will require:

for supports 2 bars 30x30x950 mm;
for crossbars 2 pieces 20x30x900 mm;
12 slats 10x20x520 mm;
12 wood screws 3x25 mm, 4 screws 3x40 mm.

Stages of work

Section assembly is performed on any flat surface. From upper parts the supports are retreated 30 mm, and the logs are fastened with 3x40 mm screws.
Having retreated 500 mm from the attachment point of the upper cross member, a similar installation of the lower beam is carried out.
The slats are fastened first from left to right, using 3x25 mm screws. At the point of attachment of the upper cross member and the support, the first rail is mounted, to the lower frame - at a distance of 150 mm from the support. Their subsequent installation to the purlins is carried out in increments of 150 mm from the previous attachment points.
Installation of slats is done in a similar way, now from right to left. The result will be a diamond-shaped pattern.
You can fence any area, even if it has an irregular contour, by making the required number of such sections.
Important: when making a square or rectangular shape, the material consumption will be much less than when constructing a multifaceted structure.
The finished structure is painted with alkyd paint of the same color or coated with a protective varnish. You can give your fence a more “joyful” look if you paint it in multi-colored tones.

"Wattle"

This kind of fence can be completed in a fairly short time.

It is better to cut willow, birch or apple twigs for its production in spring or autumn, the thickness of which should not exceed 2 cm.
Quantity consumables determined by the height and length of the structure. In general, to implement this idea you need stakes or bars, rods, wood screws, and wire.

Tip: instead of vines, you can use old multi-colored hoses or wires with a rubber sheath.

Stages of work

As a rule, vertical supports are installed in increments of 0.5 m.
Weaving starts from the bottom row. The vine is fastened to the first support using wire or screws. Next, the rod is passed in a horizontal direction, bending around each bar. It is recommended to fix the joints of the rods with wire.
If there is no desire or opportunity to study self-production fencing of this kind, you can purchase a ready-made version. For example, modular fences up to 0.5 meters high made of natural pine are offered. Treatment with antiseptic solutions and painting with varnish to give the lamellas an attractive appearance is carried out in the factory.

Those who care not only appearance fence, but also its strength and resistance to precipitation can opt for products made from wood-polymer composite. This material makes it possible to produce sections of any complexity and configuration.

Decorative fences for flower beds made of stone

Cobblestones of various shapes are selected for masonry, thus creating a fence of the “medieval” period. Here the rough texture of the stones will create a wonderful contrast with delicate flowers and greens. Without exaggeration, it will last forever.

Stages of work

The material can be sandstone, dolomite, shungite, both round and bedded. As a rule, the first row is laid out on concrete mortar, trying to use slab-like rubble.
They are selected in such a way that the same row height is maintained. In this case, the masonry is done “in a staggered manner”, where the seams between the top and bottom layers should not coincide.
A sand-cement mixture will help give additional reliability to such masonry.

Metal decorative fence

Any product made from such material has a fairly long service life, but at the same time it requires maintenance - annual painting. The fence can be purchased ready-made or ordered according to an individual sketch.

But it is quite possible to make it on your own; for one section (900x550 mm) you will need:

supports - 2 reinforcements Ø 12 mm and length 950 mm;
crossbars - 2 reinforcements Ø 12 mm, length 900 mm;
horizontal crossbars - 5 rods Ø 10 mm, length 39 cm;
decorative elements - 6 rods Ø 10 mm, length 14.5 cm;
welding machine.

Stages of work

Step back 50 mm from the top of the supports and weld the cross member, measure 40 cm from it and mount bottom part frame.
Horizontal crossbars are attached in increments of 150 mm.
Next, decorative vertical elements in a checkerboard pattern. To do this, a rod is first welded, departing 100 mm from the lower cross member, and in the next section it is attached, counting the same distance, but from the upper cross member.
Such a fence is installed by pressing its supports into the ground, leaving a distance of 100 mm from the ground to the bottom of the frame.

Manufacturers also offer galvanized borders, intended not so much for fencing flower beds, but for creating them. They are available in heights of 17 cm and lengths from 25 to 100 cm, which allows you to design flower beds quite in an original way. Thanks to the universal connection, there is a great opportunity to assemble a flower bed from them different sizes and in the form of any geometric figure.

Decorative concrete fences

Of course, when many people mention such material, they associate it with a massive, gray fence. But don’t rush to give up concrete products; there are various options borders intended for garden paths, fencing lawns and decorating flower beds.

These products have not been produced in dull colors for a long time; now they can be of different shades and have a pattern on the front surface.
Making this kind of fence yourself will not be difficult if you use decorative fence molds made of polyurethane or plastic.

Stages of work

All work consists only of lubricating the matrix and filling it with concrete mixture.
Next, you need to let the solution harden (24 hours is enough) and you can remove the finished section. Thus, it is prepared required quantity curb stones.

A few tips

the matrix can be lubricated with ordinary vegetable oil;
For the solution, take one part of M250 cement and two parts of sand, add enough water to make the mixture thick;
The more sand in the mixture, the darker the product will be.
if you plan to paint a concrete fence, then before doing this it is necessary to treat it with a deep penetration primer.

Decorative brick fence

This material firmly holds a leading position as a fencing for lawns, flower beds, lawns and paths in the garden and country house. This is due to its characteristics, availability and ease of installation.

Stages of work

Typically, the brick is laid along the perimeter of the flowerbed at an angle on its end side, creating a kind of “jagged” fence.

But there are several more ways to do masonry:

lay clinker around the flowerbed, forming a circle or oval. The second row is done in the same way, making sure that the seams do not match the previous layer. Masonry is done without concrete mortar, so the design is unreliable. But it can also be done using a sand-cement mixture;
perform the first two rows using conventional masonry using concrete mortar. The clinker in the next row is placed on a spoon (this is the narrow and long side of the brick). Since the width of this layer is greater here, alignment is carried out along the inside of the masonry;
the brick can be placed on the butt (on its narrow, short side). The seams between them can be quite wide - about 2 cm.

Photos of decorative fences made by yourself

Car tires are most often used to create flower beds and flower beds. They also separate beds, paths, and lawns by simply digging them into the ground;

Beer bottles can serve as a mini-fence by placing them upside down. The use of bottles made of white, green, and brown glass will help to add even more originality to this design;

Plastic 5-liter water bottles will work just as well. They are filled with colored pebbles or sand so that they do not lose their shape, and the top is painted with any color;

logs Ø 15-20 cm are dug or driven into the ground close to each other; any lumber left over from the construction site is suitable for this purpose.

Every owner of a summer house, vegetable garden or garden dreams of creating an ideal design on his land space. And for this it is not at all necessary to purchase expensive factory-made fences; it is quite possible to make them, for example, from the material left over after building a house, and using all your wild imagination. You can take one type of material or combine them, thereby giving the surrounding area an amazing and rather original look.

One of the important elements of a country house is the fence. It defines the boundaries of the site and serves as protection from prying eyes. Increasingly, the fence also serves a decorative function. In this article we will look at how to make a decorative fence with your own hands, without turning to specialists for help.

Fencing materials

Decorative garden fencing can be made from many building materials.

Wooden fences deserve special mention:

The installation process is simple
The prices for the material are quite reasonable.
This fence can be painted in any color that seems appropriate.

Stone fences are no less popular. This type of fence does not require any special maintenance after installation.

Pay attention! A fence should not only be aesthetically pleasing, its main quality is strength and durability!

There are options for making decorative fences from plastic, concrete, brick, bottles and more. Below we will take a closer look at each of the existing ones.

Plastic fence

As a rule, plastic fencing can be purchased ready-made on the market or in specialty store. This material has positive technical characteristics, especially thermoplasticity. Plastic fences can be used to fence flower beds, sidewalks, and front gardens. Manufacturers plastic fences use a variety of colors and shades

Here are just some of the features and positive characteristics of plastic fencing:

There are strip and sectional fences. They are ideal for marking the boundaries of a garden path. In addition, they will be a wonderful addition to a flower arrangement.
Each section has pegs. Thanks to this, their installation is not difficult. Using light pressure on the fence, the pegs need to be driven completely into the ground. Installation is possible both on a flat and inclined surface.
Thanks to modern developments, such a fence can imitate wattle fence, wooden picket fence, masonry, etc. Typically the section height is 130–200 mm.

Decorative wooden fence

Wood is the most common material used to make decorative fences for flowers and more. The tree does not create disharmony in the garden; it looks at ease. The main advantage is the availability of the material. To make a decorative fence, you can use different lumber: branches, logs, slats and boards. However, regardless of the type of wood used, it should be carefully treated at the beginning. This is especially true for the part that will be immersed in the ground. For example, this part can be treated with liquid bitumen. The other part of the structure must be impregnated with a special solution, which will prevent rapid rotting and repel insects. Let's look at the features of manufacturing three types of wooden fences:

Boardwalk.
Lattice.

Manufacturing of plank fencing. Let's look at an example of making a board fencing with your own hands measuring 700x700 mm. To do this you need to prepare:

four bars 5×5×70 cm,
eight boards 2×10×70 cm,
40 wood screws or nails,
hammer or screwdriver,
level.

The work process looks like this:

Supports are driven into the ground at a distance of 70 cm from each other. Using a level, the vertical is checked, and the height is also adjusted.
Then the board is attached to the top of the block so that its edges do not protrude beyond the edge of the block.
The second crossbar is installed at a distance of 10 cm from the bottom edge of the board.
The entire board fence is installed in this sequence.

Manufacturing of decorative fencing such as lattice. This fence is suitable for a small flower bed. It can also be used to fence a recreation area. One section in our case will be 90×63 cm. For manufacturing you need:

two bars for support 3×3×95 cm,
two bars for the crossbar 2×3×90 cm,
twelve slats measuring 1x2x52 cm,
four self-tapping screws 3×40 mm and 3×25 mm – 12 pieces.

The whole DIY manufacturing procedure boils down to the following:

The process of assembling sections is carried out on a flat surface. It is necessary to retreat 3 cm from the top, and then secure the bars with self-tapping screws.
Step back 50 cm from the place where the upper crossbar is attached, then install the lower beam according to the same principle.
The slats must be secured from left to right with a 3x25 mm self-tapping screw. Having retreated 15 cm from the support, the first rail is fixed at the upper point of attachment of the crossbar and support. The slats are installed in 15 cm increments.
Each rail is installed in a similar manner from right to left. This creates a diamond-shaped pattern.

To fence your plot or flower bed, you should make the appropriate number of sections.

Pay attention! If you decide to make a decorative fence of a rectangular or square shape, then the consumption of building material will increase several times.

When the fence is installed, it should be painted or coated with a protective varnish, which will protect the structure from rotting. If desired, the fence can be painted in several colors, which will make the area more cheerful.

Decorative wattle fence. As for this option, it is done quite quickly. To do this, you will need to get willow, birch or apple branches. It is best to cut them in the fall or spring. The thickness of each branch should be no more than 20 mm. The consumption and volume of branches required will entirely depend on the size of the decorative fence. In addition to the branches, you will need to prepare the following material:

wire,
wood screws,
bars.

Pay attention! Some modernize this idea and use wires or multi-colored hoses instead of willow branches!

So, all the work proceeds in the following sequence:

Vertical supports are installed in half-meter increments.
As a rule, you should weave starting from the first row. Using screws or wire, a vine is attached to the bottom of the support. Then it is stretched horizontally, bending around each subsequent beam/support. So that after a while, when the branches dry out, the structure does not fall apart, it is recommended to fasten each end with wire.

In principle, this is the entire technology for making a decorative fence with your own hands using the weaving method. There are other interesting methods for making fences, more on that later.

Decorative stone fence

In this option, you can use cobblestones of various shapes. The result may be a fence in the style of the Middle Ages. With delicate flowers, the rough texture creates an excellent contrast. Such a fence will last for centuries, and this is without exaggeration. The work plan for making such a fence is quite simple:

The first row of stones is best buried and laid on cement. It is preferable to use flat stones.
The stones are selected to be approximately the same height. This will allow you to construct subsequent rows without less problems.
To make the structure durable, each stone is connected with a cement composition.

Pay attention! During the laying process, the seams should not coincide; it is necessary to lay the stones staggered.

Metal fence

Every metal fence has one main advantage, which is durability. However, metal fences will require additional annual painting, otherwise their appearance will not be pleasing. A metal fence can be purchased ready-made and assembled according to plan. You can think over the layout yourself and, accordingly, make a metal fence yourself. Let's consider brief instructions for the production of a metal section measuring 90×55 cm. To do this, you need to prepare:

two fittings Ø1.2 cm 95 cm long for support,
two fittings Ø1.2 cm 90 cm long for crossbars,
five rods Ø1 cm 39 cm long for a horizontal crossbar,
decorative elements: six rods Ø1 cm, length 14.5 cm,
welding machine.

Work on the manufacture of a metal decorative fence looks like this:

From the top you retreat 5 cm from the support, after which you weld the cross member.
Next, measure 40 cm from it and mount the lower part of the frame at this distance.
Fix the horizontal bars in 15 cm increments.
Weld the decorative elements in a checkerboard pattern.
Installation of the fence is carried out by pressing the supports into the ground.

Pay attention! The distance from the bottom of the frame to the ground must be at least 10 cm.

Of course, the work on making this type of decorative fence will take you much more time. But such a fence will last much longer.

Decorative concrete fences

You can often find a massive gray concrete fence that can hardly be called decorative. However, thanks innovative technologies a concrete fence can be of a variety of colors and shades, and there may be a pattern on the front part. You can make such a design with your own hands; you just need to purchase or make special molds. The work process is quite simple. Concrete is poured into the matrix for a day. After drying, the section is removed and installed. Everything is simple and consistent. Follow these tips:

Each matrix must be lubricated with vegetable oil before pouring concrete.
Recommended brand of cement is M250.
To prevent the product from turning out dark, there should be less sand in the total mass, and vice versa.
Before painting finished product It is recommended to treat the surface with a deep penetration primer.

Decorative brick fence

The most popular material for arranging flower beds, lawns, and lawns is brick. He has exclusively positive properties. In most cases, it is laid in a diamond shape, resulting in a jagged fence. But this is not the only installation method. You can lay out fences in the shape of an oval or circle.

The second row is laid so that the seams do not match. Each brick level is fixed cement mortar so that the structure is durable. This way you can create a beautiful decorative fence with your own hands.

A non-standard decorative fence that harmonizes with the exterior of the house will attract the views of all neighbors in their summer cottages. If you make a decorative fence with your own hands from scrap materials, it will give you pleasure from the work done and pride in your creation. It is not difficult to carry out such work. It is necessary to come up with a design for a decorative fence, study the materials used and the principle of construction of the structure.

Beautiful fencing for a personal plot

Houses and surrounding areas have always been fenced. Now such a building not only encloses the site, but also has a design function, emphasizing the individual characteristics of the house and its owners.

The most traditional type of wooden fence: neat painted picket fence

Decorative fences are a mandatory sign of a well-groomed area. They divide the territory into zones and delight the eye with their appearance. To build them you need creative ideas and opportunities for implementation.

Fences are created to implement the following functions:

Decorative – to decorate the area around the house.
Division of zones - divides the territory into recreation areas, garden, vegetable garden, swimming pool, etc.
Protective – for fencing from neighboring residential areas.
Barrier – restricts passage to a forbidden place on the territory. Used when there are small children.

An example of a concrete fence on a site

Let's define what a decorative fence is. The structure has a small height. It can be created for artificial lake and other details of the house's exterior.

Owners of summer cottages often make a ledge to separate the alley or paths from the rest of the lawn. The fence is additionally illuminated with solar-powered lanterns.

Identical fences are installed to highlight similar zones and create a complete design of the territory: large stones of the same type are laid out, and a low plastic ledge is laid along the entire perimeter of the beds.

Fence from willow twigs for the garden

The height and length of the decorative fence is determined by the place of its application.

For flower beds and gardens, barely noticeable fences are needed; walls 1 meter high and higher are used to protect the territory. They are made from heavy, massive materials.

The design of the fence does not have to be invented. To do this, you can use the Internet. The network allows you to study a large number of photos depicting different ones made with your own hands from scrap materials.

Drawing of a forged decorative fence

Advantages

If you decide to make a decorative fence with your own hands, it will decorate the area garden plot and such construction will save cash. This fencing is distinguished by a variety of shapes and types, which allows you to create it elegant and functional.

Wooden fence for the front garden

It is made entirely from different materials, therefore, creating a hedge gives freedom to the artist’s creativity. The materials from which such barriers are made can be found even in the forest.

If this is not possible, you will have to buy raw materials. In any case, it will be cheaper than hiring workers to install permanent fencing.

Option for making a dividing line from rods

Flaws

The disadvantage of a decorative building is its unreliability. Since it is not permanently installed, the building is susceptible to demolition due to hurricanes and strong winds, especially in the suburbs. If a decorative fence is installed around the perimeter of the dacha area, it will not save you from robbers and intruders.

Despite all the positive aspects, such protection is easy to overcome

Each material from which the fence is made has its own disadvantages:

Concrete structures have high cost compared to other materials. They require a foundation to be installed on the ground. Only after this can you begin to build the fence. In this case, you will not be able to cope on your own, since such a fence has a lot of weight. You will have to hire a specialized car.
or wooden structures have increased flammability. Therefore, due to a fire, the tree may completely burn out and the fence will need to be rebuilt. To avoid this unpleasant moment, you will need to spend money on fire-fighting agents that are used to process such material. However, the main disadvantage of such a structure is that it is short-lived.
Plastic buildings quickly fade in the sun and become dull. Because of this, the barrier has to be thrown out and a new one installed, because general view the area is deteriorating. Plastic often breaks, which means that the fence must be constantly monitored and prevent mechanical damage. Many manufacturers commit the sin of using toxic raw materials when making fences, so living next to such a fence will be unsafe.

An example of making a beautiful fence with a minimal budget

Ideas for constructing wooden barriers

Building design can get boring at any time. The owner’s task is to build the fence so that, if necessary, it can be easily dismantled.

When designing, craftsmen sometimes use two or more types of materials. Thus, the fence becomes especially attractive and makes the eye stop on it. When choosing raw materials, you need to be guided by your capabilities and goals. In order to do right choice, you should study photos of finished fences, as well as each material separately.

The choice of one model or another is directly dependent on the budget

Tree

Installation diagram of the foundation and picket fence

It is important to remember that a wooden fence does not last long. It must be painted every year to prevent the wood from rotting from natural exposure.

Blanks made of wood are designed in the form of a picket fence, chessboard, wickerwork, lattice or vertical. Most often, owners of summer cottages install classic vertical columns. This type of structure combines simplicity of design and installation.

Drawing for installing a wooden fence on metal poles

Trees are used to make DIY wooden creations coniferous species. Usually they take cedar or pine. This wood is more resistant to natural influences and therefore lasts much longer than other raw materials.

Plan for a wooden fence on concrete supports

Stone

Stone barriers have been produced since the time of human exploration. labor activity. They are highly durable, reliable and beautiful. Making a garden fence with your own hands will not be easy, but the result will not disappoint. All materials for production can be found in nature.

The photo shows a stone fence.

The process of laying a stone wall fence

Boulders, gravel, limestone, dolomite stone and crushed granite are used in fencing. If there are no stones suitable for building in the area surrounding the dacha, you can buy them. Artificial stone is especially popular.

It looks no worse than natural, but costs several times less. However, erecting a building made of stone is a very long and labor-intensive process. It requires attention and patience.

Sketch with dimensions of the main elements of a natural stone fence

The most important advantage of stone raw materials is its natural texture. The finished fence does not require additional parts, since it has the necessary decorative qualities. Photos of such barriers convey the uniqueness of each stone.

Drawing of a metal picket fence with dimensions

Among the shortcomings are:

Heavy weight of raw materials. To move it, you will need to rent special equipment.
Annual anti-corrosion treatment.

It is quite possible to build a metal structure relying on your own strength. For her self-construction availability will be required special tools and welding equipment. There are a large number of articles and books that describe step-by-step the installation of a metal workpiece.

Scheme for installing a dividing line from a chain-link mesh

Brick fence diagram

A brick fence has the following advantages:

reliability. If you install a brick fence in accordance with all standards, it will protect your summer cottage from the effects of external natural irritants and strong gusts of wind;
durable use. Brick is not afraid of sudden changes in temperature and pressure, so it will withstand any natural conditions;
unnecessary maintenance. The brick structure does not have to be painted or covered protective materials. It is strong and therefore copes with natural influences on its own;
appearance. Brick can add sophistication to a home.

The photo shows a beautiful brick fence.

Example of construction combined with overall aesthetics

You won't be able to save on the cost of bricks. It must be of high quality, but it is always expensive. However, building a structure with your own hands will avoid additional expenses.

Assembling modules from concrete significantly reduces construction time

Concrete is heavy, so special equipment is required to transport it. This consists additional costs on concrete decoration. When choosing a concrete fence as a fence from neighbors' summer cottages, you should focus on the size of the territory.

DIY concrete fence installation diagram

It is easy to build a concrete building yourself, since it is a prefabricated structure.

Plastic

Decorative plastic fencing is installed to decorate flower beds and alleys in a summer cottage. It is short-lived and fades quickly. If there is a sudden change in pressure, the plastic may burst. It should also not be used as protective fence, because it will not protect against anything.

Appearance of a plastic fence

The advantages of a plastic fence are:

ease and speed of installation;
low cost of material;
ease of use.

Plastic fencing products often imitate natural materials. By spending a minimal amount of money, you can depict any composition on your site.

Pattern of country fencing made of plastic in the form of wicker

It is a dense vegetation of the required length. To create a living fence, coniferous or deciduous trees are used. Less commonly used ornamental plants. In dacha conditions, living plantings are most often used.

The photo below shows a hedge.

The idea of protection from living plants

The plant hedge is regularly formed using scissors and pruning shears. An unusual fence requires special care to keep it looking beautiful.

Pros of a living fence:

changing shape at any time;
unusual solution;
budget option;
environmental conservation;
protection from dust and wind.

Scheme and rules for creating a hedge

Growing a green hedge requires a long time and constant care. If these factors do not frighten the owner of a summer cottage, he will grow beautiful fence, forcing you to attract the attention of all passers-by.

From scrap materials

To make a decorative fence from scrap materials, suitable glass bottles, tires, pipe cuttings, rods, etc. Almost any recycling product is suitable for building a country fence.

Fence made of glass containers

Glass bottles can be beautifully color-matched, laid and secured with cement. A vertical barrier is also built from bottles. To do this, the bottom of the bottle needs to be drilled. Each bottle is threaded onto a metal pin. Several of these structures are installed vertically. Bottles can be painted in different colors.

A shape for a flower bed is cut out of tires, painted and plants are planted. Several made flower beds will decorate the garden plot.

Ideas for creating flower beds from waste tires

Probably, each of us cannot remain indifferent to the living and vibrant beauty flower beds. Nevertheless, the decorative fences and fences that frame them also attract attention and remain in the memory. Moreover, the latter, talentedly decorated, sometimes deserve more attention than the flowers themselves.

Of course, the main purpose of decorative hedges and enclosures is precisely decoration, in harmony with other elements of the landscape. At the same time, fences turn the flowerbed into a complete composition, divide the space, and also protect the flowers from the excessive attention of children and animals.

The fence is small, but remote: it both decorates and protects

What types of fences are there for flower beds?

There are fences different types, and the choice depends on the specific purpose that the flower fence will serve:

If you just need to separate the flower garden from the lawn, then a mini-fence up to 7cm in size will do.
In the case where the flowerbed fencing is also a border for the garden path, make the height of the fence 10 cm.
If you need to block the roots of flowers or plants, pay attention not to the height of the fence, but to the level of its immersion in the ground. It must provide sufficient strength, for example, brickwork or plastic tape.
When it is necessary to protect flowers from cats, dogs, and overly curious children, make a fence at least 0.4 m high. Of course, the flowerbed will look unaesthetic if it is covered with a solid fence. Use a wooden, plastic or metal picket fence that will make your fence translucent.
Products up to 50cm in height are suitable for a rose garden, because they will not be conspicuous against the background of tall and lush flowers.
For a mixed border of low flowers and plants, flat pebbles, paving stones or a border for paths laid out along the perimeter of the flower garden are sufficient.

Traditional wooden fencing

Wooden fence on metal frame- combination of simplicity and reliability

Wood is one of the most commonly used materials when constructing a hedge for a flower bed. It does not heat up from the sun, is completely safe for plants, economical, convenient and pliable for skilled construction hands. It’s not difficult to install the simplest one yourself wooden fence for a flower bed of twigs, slats, logs, planks, slabs.

A significant drawback is its fragility, susceptibility to the destructive effects of water, sun and wind, which can be solved to a certain extent by various impregnations and regular painting.

What are they? wooden fencing:

a border made of logs, that is, stakes buried in the ground;
picket fence: it can be simple, from identical ordinary strips; and complex - made of planks of various sizes and qualities;
mosaic from wood cuts or cross sections of logs.

Making a fence from wooden pegs

Limiting a flower bed with logs of wood is one of the most common and simple types of fencing a flower garden in the private sector, in a country house or in a personal plot. You will need logs of the same diameter. Choose the height according to your wishes, but keep in mind that 20cm should be driven deep into the ground. A high-quality fence made from logs carefully treated with antiseptic will last up to 10 years.

It is important to treat a log fence well to prevent rotting.

prepare logs of the required length;
clean them of bark and treat them with an antiseptic, otherwise the logs may quickly rot;
dig a ditch twenty centimeters deep around the perimeter;
install the chocks evenly and tightly;
compact the soil well and cover with soil.

Making a fence from boards

A board fence for a garden turns out to be beautiful and “translucent” because the boards are mounted at a certain distance from each other. It is more difficult to make than the previous type. Step-by-step recommendations:

prepare timber, boards, wood screws or regular nails, a screwdriver or hammer;
drive support beams into the ground vertically and at the same height level in increments of 0.7 m;
fasten the boards horizontally to the top of the beam, the end part of the board should not protrude beyond the beam;
the next board is installed 10 centimeters lower from the edge of the board installed earlier;
This system of fastening boards is carried out for each section.

In addition to the fence itself, it is important to make a gate into the garden

Decorative homemade “lattice”

It is good to fence tall plants and flowers in the garden with a light and translucent “lattice” fence, which is easy to make with your own hands. A “lattice” of large wide slats will help you decorate and thematically divide zones on your garden plot, for example, separate a recreation area or a storage area for equipment from the general area of the site.

Take two beams each as supports for one section and slats for the crossbars, wood screws 3x30mm and 3.5x45mm. You'll need a screwdriver; a hammer won't help.
Drive in the supports.
Stepping back 30 millimeters from the top edge of the support beam, attach the logs. Use screws measuring 3.5x45mm.
Attach the lower transverse board at a distance of 0.5 m from the upper joist.
Fasten the first slats from left to right. Use screws measuring 3x30mm. The first plank is installed at the attachment point of the upper log and to the lower frame 10 cm from the support beam. The following slats are attached with a gap of 10cm.
Then all subsequent slats are fixed. As a result, you will get a beautiful patterned fence.

Decorative fence made of slats

Basket made of wicker

This type of fencing is not very durable, but it looks original. The basket “weaves” along the perimeter of the round flower bed. The wattle fence pleases the eye and protects plants and flowers. You can make a decorative “basket” with your own hands from branches or twigs of vines, hazel, birch branches, and grapevines. Branches for fencing must first be cleared of bark. The smaller the diameter of the structure, the greater the height of the fence.

Fencing for flowers made of vines

Country decorative fence made of branches

A wicker fence will decorate your flower garden and help decorate personal plot in country style. Wattle is also made from twigs or vines, wires, multi-colored hoses and anything that looks like twigs - use your imagination and get an original decoration!

Wood-polymer composite is popular, which lasts a long time and does not react to precipitation. The stakes can be pieces of reinforcement or plastic tubes. Sequence of making braids:

Start with the supports. Install them at a distance of 50 centimeters from each other.
Start weaving from the bottom. Attach the vine to the first support with wire or screws, then let it go around each support post.
Secure the junctions of the rods with wire. The weaving system is uniform throughout the entire diameter of the basket.
After finishing the weaving process, you can treat the twigs with an antiseptic to prevent rotting. Do you want to make your basket even more aesthetically pleasing? Coat the product with varnish.

Decorative fence made of branches

Metal fencing

Decorative cast iron and iron fences are popular among owners of villas, large personal plots, lovers of elite and expensive style in the private sector. Forged fences look expensive; they are made by special companies individual orders. Such fences are durable and look very beautiful. You need to choose them very carefully, coordinating the design with the overall landscape. The only negative is that such products are quite expensive.

A plastic fence looks like a forged metal fence

Plastic fencing

Plastic is quite popular in the manufacture of fences for flower beds and flower beds. Advantages of plastic products:

variety of shapes, colors and sizes;
ease of manufacture and installation;
durability - plastic resists precipitation, moisture, ultraviolet rays;
the ability to easily select a product that suits your overall design landscape.

Types of plastic fencing

Plastic fence for flower beds - fast, cheap and beautiful

Decorative plastic fence comes in different types. Sectional fences can come in a variety of shapes and colors, and they already have stakes for installation. Just drive pegs into the ground and your low fence is ready. Plastic borders can take any shape, which will allow you to make a flowerbed of the desired shape. They can be smooth or have a surface structure with a pattern; imitation of stone or brick is possible. The simplest option is a roll plastic tape.

The fence is hand-cut from a piece of plastic

Tips for installing plastic products:

You can decompose what you have purchased plastic product under the sun. Warm plastic will be more pliable and easier to install and will take the desired shape.
Dig a hole in the ground.
Measure the ribbon to the desired length. Use a staple gun to join the pieces of tape together.
Place the plastic in the groove and tamp down.